Meltem M-WRG-II E-F Operating And Installation Instructions Download Page 36

Page: 36 / 60

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 36 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

12 Filter maintenance

The ventilation unit has a runtime-controlled filter monitoring function with visual display.

It monitors the time since the last air filter change. If the last air filter change was more

than one year ago, the filter change display is activated and a pending air filter change is

signalled by LED 1, which lights up constantly (see Fig. 12 on page 23).
No tools are needed to change the air filters.

NOTICE

► Follow the instructions for changing the air filters in section 6.3 on page 22.

12.1

Choice of filter

The following air filters may be used or are available for selection for the M-WRG-II venti-

lation units:

Part no. Type

Filter type

Filter class

Application

750010 M-WRG-II FA Outdoor air

filter

ISO ePM1

60% (F7)

Effectively filters out respirable

particulates such as pollen,

soot and bacteria from dust

class PM1

750020 M-WRG-II FK Activated

charcoal filter

(optional for

outdoor air)

ISO ePM2,5

55% (F7)

Effectively retains respirable

particulates such as pollen,

soot and bacteria from dust

class PM2.5, and the acti-

vated charcoal layer absorbs

odours and harmful gases

such as propellants, nitrogen

oxides, ozone and solvents

750000 M-WRG-II FS Extract air

filter

ISO Coarse

60% (G4)

Effectively retains coarse

particulates such as house-

hold dust >PM10

Table 3: Choice of filter

12.2

Ordering filters

Please contact your local or regional dealer for information on ordering

filters. You will find the contact details on our website at

www.meltem.com

(or using the QR code on this page).

Go to

www.meltem.com

Summary of Contents for M-WRG-II E-F





























































Search results

Summary of Contents for M-WRG-II E-F

Reviews:

Related manuals for M-WRG-II E-F

Brands by name

Popular brands

Meltem M-WRG-II E-F, Operating And Installation Instructions

Search results

Summary of Contents for M-WRG-II E-F

Reviews:

Related manuals for M-WRG-II E-F

Brands by name

Popular brands