Meltem M-WRG-II E-F Operating And Installation Instructions Download Page 15 | Manualshive

Page: 15 / 60

background image

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 15 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

3

Warranty and liability

3.1

Warranty

The following cases shall invalidate the warranty:

— The installation kit was not installed as described in the installation manual.

— The ventilation unit was not installed as described in the installation manual.

— The ventilation unit was flush-mounted without using a flush-mount installation kit.

— Genuine parts/genuine air filters were not replaced with genuine parts.

— Unapproved changes were made to the installation kit or ventilation unit.

— Repairs were not carried out by Meltem or by an authorised specialist company.

— The ventilation unit was operated without air filters and outer wall terminals.

— The warranty does not cover wearing parts such as air filters.

3.2

Liability

The manufacturer’s liability shall not apply in the following cases:

— The installation kit was not installed as described in the installation manual.

— The ventilation unit was not installed as described in the installation manual.

— The ventilation unit was flush-mounted without using a flush-mount installation kit.

— Genuine parts/genuine air filters were not replaced with genuine parts.

— Unapproved changes were made to the installation kit or ventilation unit.

— Repairs were not carried out by Meltem or by an authorised specialist company.

— The ventilation unit was operated without air filters and outer wall terminals.

«
...
13
14
15
16
17
...
»

Summary of Contents for M-WRG-II E-F





























































Reviews:

No comments

Related manuals for M-WRG-II E-F

Brand: jablotron Pages: 48

Brand: ebm-papst Pages: 12

Brand: Hunter Pages: 17

Polifemo BREEZE

Brand: Argo Pages: 8

Smarty 3X VE Series

Brand: Salda Pages: 52

Brand: ORIGO Pages: 10

Air Shadow FP815FS

Brand: Fanimation Pages: 14

Brand: ebm-papst Pages: 12

Brand: EuroFans Pages: 17

Brand: Monte Carlo Fan Company Pages: 5

Brand: Olimpia splendid Pages: 7

Brand: Venture Industries Pages: 25

Brand: Sulion Pages: 24

Brand: Zehnder Rittling Pages: 76

Brand: Fujitsu Pages: 10

Brand: Fujitsu Pages: 12

Brand: Fujitsu Pages: 23

Brand: Fujitsu Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands