Meltem M-WRG-II E-F Operating And Installation Instructions Download Page 39

Page: 39 / 60

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 39 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

12.3.5 Inserting the new outdoor air filter

► Carefully guide the new outdoor air

filter (item 1 in Fig. 22) into the venti-

lation unit.

► Make sure that the air filter slides into

the 3 retaining tabs (item 2 in Fig. 22)

on the back wall of the ventilation

unit.

► Place the filter cover (item 3 in

Fig. 22) on the outdoor air filter. Make

sure that the filter cover lies flat on

the intermediate plate (item 4 in

Fig. 22).

► Turn the filter cover clockwise until

the arrow on the filter cover (item 5 in

Fig. 22) lines up with the arrow for the

locking position (item 6 in Fig. 22). Make sure that the 3 tabs (item 7 in Fig. 22) on the

filter cover engage in the retainers (item 8 in Fig. 22) on the intermediate plate.

► Check the position of the filter cover. The hand grip must be vertical and the arrow

on the filter cover must line up with the arrow for the locking position (see Fig. 20 on

page 38).

NOTICE

— The ventilation unit will not work as well if the filter cover is not inserted correctly.

— Only M-WRG-II FA, part no. 750010, and M-WRG-II FK (activated charcoal filter),

part no. 750020, may be used as the outdoor air filter. The part no. and air filter

class are imprinted on the turqoise end plate of the air filter (item 9 in Fig. 22).

12.3.6 Attaching the unit cover to the ventilation unit

► Hold the cover (item 1 in Fig. 23) of

the ventilation unit with both hands

and tilt the top edge of the cover

towards the ventilation unit.

► Insert the tabs (item 2 in Fig. 23)

of the unit cover into the retainers

(item 3 in Fig. 23) on the top of the

ventilation unit.

► Lightly press the bottom edge of the

cover against the ventilation unit until

you hear the cover snap in place.

Fig. 22: Inserting the new outdoor air filter

Fig. 23: Attaching the unit cover to the ventilation unit

Summary of Contents for M-WRG-II E-F





























































Search results

Summary of Contents for M-WRG-II E-F

Reviews:

Related manuals for M-WRG-II E-F

Brands by name

Popular brands

Meltem M-WRG-II E-F, Operating And Installation Instructions

Search results

Summary of Contents for M-WRG-II E-F

Reviews:

Related manuals for M-WRG-II E-F

Brands by name

Popular brands