McHale 900340 Operator'S Instruction Manual Download Page 29

Page: 29 / 155

McHale

Fusion Vario

Baler & Wrapper

Knives of the cutting device should only be removed
with an appropriate tool and protective gloves

(CST00112)

Turn off and remove key from tractor.
Read and understand the manual before working on or
performing maintenance on the machine.

(CST00113)

Close protective covers before operating the machine

(CST00114)

Hydraulic accumulator is under high pressure.
Slowly release hydraulic pressure before carrying out
any maintenance.

(CST00115)

Beware of rotating dispensers, ring and moving
wrapping table rollers

(CST00116)

Knife release lever:
horizontal position-locked
vertical position-unlocked

(CST00118)

Keep hands out of the crush area between the roller
and chassis rail

(CST00120)

Maximum hydraulic pressure and maximum PTO
speed. This machine must not be connected to
hydraulic systems with pressure higher than 210 bar.

(CST00121) - 540 rpm PTO/gearbox speed
(CST00814) - 1,000 rpm PTO/gearbox speed

Summary of Contents for 900340




























































































































































Search results

Summary of Contents for 900340

Reviews:

Related manuals for 900340

Brands by name

Popular brands

McHale 900340, Operator'S Instruction Manual

Search results

Summary of Contents for 900340

Reviews:

Related manuals for 900340

Brands by name

Popular brands