Maxtor Atlas SCSI Drive 15K II Product Manual Download Page 110 | Manualshive

Page: 110 / 260

background image

SCSI Description

5-44

Maxtor Atlas 15K

5.14.6

Read-Write Error Recovery Page (01h)

The Read-Write Error Recovery page controls the drive’s response to error
conditions that arise during the course of READ (6), READ (10), WRITE (6),
WRITE (10) command processing and during the write portion of WRITE AND
VERIFY command processing. The Read-Write Error Recovery page format and
field descriptions are described in Table 5-62 and Table 5-63 respectively.

Table 5-62

Read-Write Error Recovery Page-(Page 1)

Table 5-63

Read-Write Error Recovery Page - Field Descriptions

Bit

Byte

7

6

5

4

3

2

1

0

0

PS

Rsvd

Page Code (01h)

1

Page Length (0Ah)

2

AWRE

ARRE

TB

RC

EER

PER

DTE

DCR

3

Read Retry Count

4

Correction Span

5

Head Offset Count

6

Data Strobe Offset Count

7

Reserved

8

Write Retry Count

9

Reserved

10 – 11

Recovery Time Limit

Field

Default

Value

Description

PS

1

Parameters Savable. This bit is only used with the MODE SENSE command. A returned val-
ue of 1 indicates that the target is capable of saving the page in a non-volatile, vendor-specific
location. The bit is reserved with the MODE SELECT command.

AWRE

1

Automatic Write Reallocation Enable. When the value is 1, it causes the drive to automati-
cally reallocate bad sectors encountered during a write operation. If it succeeds in replacing
the bad sector, the drive adds the revectored sector’s Logical Block Number to the Grown
Defect List. Reallocation is done only when the drive is able to recover the sector’s data un-
less the HrdBBR bit of the Maxtor (Vendor) Special Function Control Page is set.

When AWRE is 0, the drive does not automatically reallocate bad sectors encountered during
a write operation. See also Maxtor-Unique Page 39h.

ARRE

1

Automatic Read Reallocation Enable. When the value is 1, it causes the drive to automatical-
ly reallocate bad sectors encountered during a read operation. If it succeeds in replacing the
bad sector, the drive adds the revectored sector’s Logical Block Number to the Grown Defect
List. Reallocation is done only when the drive is able to recover the sector’s data unless the
Reallocate Uncorrected Errors bit of the Maxtor (Vendor) Special Function Control Page is
set.

When ARRE is 0, the drive does not automatically reallocate bad sectors encountered during
a read operation. See also Maxtor-Unique Page 39h (RUEE).

TB

0

Transfer Block. When the value is 1, the drive sends best-guess information to the initiator
when it encounters a defective sector whose data cannot be fully recovered.

When the value is 0, data that cannot be fully recovered is not returned to the initiator.

RC

0

Read Continuous. When the value is 0, the drive attempts error recovery when it encounters
an error. When the value is 1, the drive suppresses error recovery. The drive ignores any val-
ue placed in this field.

«
...
108
109
110
111
112
...
»

Summary of Contents for Atlas SCSI Drive 15K II





































































































































































































































































Reviews:

No comments

Related manuals for Atlas SCSI Drive 15K II

Brand: trueCall Pages: 16

Brand: Seagate Pages: 2

Brand: Quantum Pages: 312

FIREBALL PLUS AS 10.2

Brand: Quantum Pages: 162

Brand: Medion Pages: 2

Brand: INTILION Pages: 121

Brand: Raidon Pages: 2

LaCie Ethernet Big Disk

Brand: LaCie Pages: 47

G-RAID mini 1TB

Brand: G-Technology Pages: 13

Brand: IBM Pages: 9

Brand: 8BitMods Pages: 15

MAY2036RC Product/

Brand: Fujitsu Pages: 94

Brand: Fujitsu Pages: 130

Brand: Fujitsu Pages: 106

MBC2036RC SERIES

Brand: Fujitsu Pages: 1

MBB2073RC SERIES

Brand: Fujitsu Pages: 98

MAX3036RC SERIES

Brand: Fujitsu Pages: 94

Brand: Fujitsu Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands