manualshive.com logo in svg

Maxtor Atlas SCSI Drive 15K II, Product Manual

Share
Download
Maxtor Atlas SCSI Drive 15K II Product Manual Download Page 9

Table of Contents

Maxtor Atlas 15K

ix

5.14.3 Mode Parameter List  ...................................................................................................5-40
5.14.4 Categories of Changeable Pages  .................................................................................5-42
5.14.5 Unit Attention Condition Page (00h)  ..........................................................................5-43
5.14.6 Read-Write Error Recover Page (01h)  ........................................................................5-44
5.14.7 Disconnect–Reconnect Page (02h) ..............................................................................5-46
5.14.8 Verify Error Recovery Page (07h)  ..............................................................................5-48
5.14.9 Caching Page (08h)  .....................................................................................................5-49
5.14.10 Control Mode Page (0Ah)  .........................................................................................5-51
5.14.11 Notch and Partition Page (0Ch)  ................................................................................5-53
5.14.12 Port Control Mode Page (19h)  ..................................................................................5-55
5.14.13 Power Condition Page (1Ah)  ....................................................................................5-61
5.14.14 Information Exceptions Control Page (1Ch) .............................................................5-62

5.15  MODE SELECT (10) Command (55h).................................................................................. 5-65

5.16  MODE SENSE (6) Command (1Ah) ..................................................................................... 5-67

5.16.1 Read-Only Mode Pages ...............................................................................................5-69
5.16.2 Format Device Page (03h) ...........................................................................................5-70
5.16.3 Rigid Disk Geometry Page (04h)  ................................................................................5-71

5.17  MODE SENSE (10) Command (5Ah) ................................................................................... 5-73

5.18  PERSISTENT RESERVATION IN Command (5Eh) ........................................................... 5-75

5.19  PERSISTENT RESERVATION OUT Command (5Fh) ....................................................... 5-83

5.20  READ (6) Command (08h) .................................................................................................... 5-93

5.21  READ (10) Command (28h) .................................................................................................. 5-94

5.22  READ BUFFER Command (3Ch) ......................................................................................... 5-95

5.23  READ CAPACITY Command (25h) ..................................................................................... 5-97

5.24  READ DEFECT DATA Command (10) (37h) ...................................................................... 5-98

5.25  READ DEFECT DATA Command (12) (B7h) ................................................................... 5-101

5.26  READ LONG Command (3Eh) ........................................................................................... 5-103

5.27  REASSIGN BLOCKS Command (07h) .............................................................................. 5-104

5.28  RECEIVE DIAGNOSTIC RESULTS Command (1Ch) ..................................................... 5-105

5.28.1 Supported Diagnostics Pages Page (00h) ..................................................................5-106
5.28.2 Translate Address Page (40h)  ...................................................................................5-106

5.29  RELEASE (6) Command (17h)............................................................................................ 5-108

5.30  RELEASE (10) Command (57h).......................................................................................... 5-109

5.31  REPORT DEVICE IDENTIFIER Command (A3h) ............................................................ 5-110

5.32  REPORT LUNS Command (A0h) ....................................................................................... 5-111

5.33  REQUEST SENSE Command (03h).................................................................................... 5-112

5.33.1 Sense Data Availability .............................................................................................5-113
5.33.2 Status Reporting  ........................................................................................................5-114
5.33.3 Sense Data Format for Error Code 70h and Error Code 71h  ....................................5-115

5.34  RESERVE (6) Command (16h) ........................................................................................... 5-130

5.35  RESERVE (10) Command (56h) ......................................................................................... 5-131

5.36  REZERO UNIT Command (01h)......................................................................................... 5-133

5.37  SEEK (6) Command (0Bh) .................................................................................................. 5-134

5.38  SEEK (10) Command (2Bh) ................................................................................................ 5-135

5.39  SEND DIAGNOSTIC Command (1Dh) .............................................................................. 5-136

5.39.1 Supported Diagnostic Page List  ................................................................................5-138
5.39.2 Translate Address Page  .............................................................................................5-139

Summary of Contents for Atlas SCSI Drive 15K II





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands