manualshive.com logo in svg

Maxtor Atlas SCSI Drive 15K II, Product Manual

Share
Download
Maxtor Atlas SCSI Drive 15K II Product Manual Download Page 89

SCSI Description

Maxtor Atlas 15K

5-23

Table 5-25   

Standard Inquiry Data Page-Field Descriptions

Note:

Vendor Information, Product Identification, and Product 
Revision Level are returned as shown in Table 5-22.

Field Name

Value

Description

Peripheral Qualifier

0

Non-zero if initiator selects an invalid logical unit.

Peripheral Device

0

0 indicates that this is a Direct Access Device.

ANSI Version

3

ANSI SCSI Level 3 (SCSI-3) is supported.

AERC

0

Asynchronous Event Reporting is not supported.

NormACA

0

Does not support setting NACA in CDB Control word.

Port

0

Only used when MultiP = 1.

MultiP

 0

This field set to 1 if it is a multiport device.

Mchngr

0

Not embedded in or attached to a medium changer

ACKQREQQ

0

Device supports REQ and ACK data handshake on Q cable.

Addr32

0

32-bit wide SCSI address

Addr16

0/1

16-bit wide SCSI address

TrmTSK

0

TERMINATE TASK Function is not supported

Response Data 

Format

2

This Standard Inquiry Data is in the format specified in the International Standard.

RelAdr

0

Relative Addressing is not supported.

WBus 32

0

32-bit wide bus is not supported.

WBus 16

0 or 1

The WBus bit is 1 if the drive supports 16-bit data transfer. The bit is 0 if the drive only 
supports 8-bit transfer.

Sync

1

The drive supports Synchronous Data Transfers.

Linked

1

Linked Commands are supported.

TransDis 1

Indicates that the drive supports CONTINUE TASK and TARGET TRANSFER DIS-
ABLE messages.

CmdQue

1

The drive supports Tagged Command Queuing

SftRe 0

The drive implements the hard reset option in response to assertion of the SCSI Bus reset 
line.

VS

0

Vendor Specific

Product 

Identification

The 

value in 

this field 

is: 

ATLAS15K_18WLS, ATLAS15K_36WLS, ATLAS15K_73WLS

ATLAS15K_18SCA, ATLAS15K_36SCA, ATLAS15K_73SCA

Clocking 11

The contents of this field define the setting of the double-edge clocking option (See Chap-
ter 6). Note that the clocking field does not apply to asynchronous transfers of data. Op-
tions available are: 

Code 
00b 

01b 
10b 
11b

Description
Indicates the device server supports only Single Transition 
(ST)
Indicates the device server supports only Double Transition 
(DT)
Reserved
Indicates the device server supports ST and DT

QAS 1 

(U160)

Quick Arbritrate Support. If the value of this field is 1, it indicates that the device server 
supports the quick arbitrate feature. A value of 0 indicates that the device server does not 
support this feature. 1 is default setting.

IUS 1 

(U320)

Information Unit Supported. If the value of this field is 1, it indicates that the device server 
supports information units. A value of 0 indicates that the device server does not support 
information units. Default is 1.

Summary of Contents for Atlas SCSI Drive 15K II





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands