manualshive.com logo in svg

Maxtor Atlas SCSI Drive 15K II, Product Manual

Share
Download
Maxtor Atlas SCSI Drive 15K II Product Manual Download Page 105

SCSI Description

Maxtor Atlas 15K

5-39

5.14.2

Mode Page Types

The drive maintains three distinct sets of mode pages. They are the current page, the 
default page, and the saved page. The drive also reports a fourth set of changeable 
pages. The page types are defined in Table 5-52.

Table 5-52   

Mode Page Types

Page Type

Definition

Current

The current mode page set applies to all initiators and defines the drive’s mode. The SCSI-2 spec-
ification states that a drive can maintain Mode parameters on a per-initiator basis if it so chooses. 
The Drives do not support this option.

The current mode page set contains the values supplied in the last MODE SELECT command re-
ceived from an initiator. If no initiator has sent a MODE SELECT command since the drive was 
last reset or powered up, the current pages contain

• Saved values if saved pages exist (from a previous MODE SELECT command SP parameter).
• Default values if pages have never been saved.

The drives generate a Unit Attention condition for all initiators (except for the one that was the 
source of the MODE SELECT command) whenever one initiator modifies the Mode parameters.

Default

The default mode page set contains the factory default values that are listed in each page’s descrip-
tion.

Saved

The saved mode page set contains values preserved in the drive’s non-volatile memory by a pre-
vious SP-modified MODE SELECT command.

Changeable

The changeable mode page set provides a means for an initiator to determine which pages it is 
allowed to change and the specific bits within those pages that it is allowed to change. This page 
set is read-only and is fetched with a MODE SENSE command.

Summary of Contents for Atlas SCSI Drive 15K II





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands