manualshive.com logo in svg

Maxtor Atlas SCSI Drive 15K II, Product Manual

Share
Download
Maxtor Atlas SCSI Drive 15K II Product Manual Download Page 107

SCSI Description

Maxtor Atlas 15K

5-41

Table 5-57   

Mode Parameter Block Descriptor-Data Format

Table 5-58   

Mode Parameter Block Descriptor-Field Descriptions

Bit

Byte

7

6

5

4

3

2

1

0

0 – 3 

Number of Blocks

4 Reserved

5 – 7 

Block Length

Field

Description

Number of Blocks

This field specifies the number of logical blocks on the unit that are affected by the cur-
rent MODE SELECT command.

When this field is 0, the MODE SELECT parameters are put into effect for all logical 
blocks on the unit.

The maximum value allowed is the total number of initiator-addressable logical blocks 
for the value specified in the Block Length field.

A value that is less than the maximum value will decrease the number of initiator-acces-
sible logical blocks to the amount specified.

Block Length

This field specifies the length, in bytes, of each logical sector.

Summary of Contents for Atlas SCSI Drive 15K II





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands