manualshive.com logo in svg

Maxtor Atlas SCSI Drive 15K II, Product Manual, Page: 37 / 260

Share
Download
Maxtor Atlas SCSI Drive 15K II Product Manual Download Page 37

Installation

Maxtor Atlas 15K

3-9

3.4.2.2

Delay Spin (DS), Stagger Spin (SS)

Maxtor Atlas 15K  drives have three Spin Up modes:

Option 1 (No jumpers installed):

Spin up immediately when power is applied. Verify that no jumper is installed 
across the Delay Spin pin pair of the J3 Option Header.

Option 2 (Delay Spin jumper installed):

Spin up on START STOP UNIT command: Install the jumper across pin pair 
11/12 (GND/Delay Spin) on the J3 Option Header. Remove any jumper from 
pin pair 21/22 (GND/Stagger Spin) if a jumper is installed there, on the 
Secondary Option connector.

3.4.2.3

Single-Ended Operation – Force SE (Disable LVD)

Install a jumper across pin pair 13/14 (SE) on the J3 Option Header to operate the 
disk drive as a single-ended device. Remove the SE jumper for LVD operation and 
monitoring of the DIFFSENS signal.

3.4.2.4

Remote Busy and Fault Displays

Busy and Fault status of the drive can be monitored remotely by connecting a remote 
(external) Busy and/or remote Fault display LEDs to the 17/18 pins on the J3 Option 
Header or the J1 Option Connector. 

Remote Busy LED

On the J3 Option Header, connect the cathode side of the remote Busy LED to 
pin 18, Busy Out. Connect the anode side of the LED to pin 17, +5V.

On the J1 Option Connector, connect the cathode side of the remote Busy LED to 
pin 8, Busy Out. Connect the anode side of the LED to pin 11, +5V.

Remote Fault LED

On the J3 Option Header, connect the cathode side of the remote Fault LED to 
pin 9, Fault LED. Connect the anode side of the LED to pin 17, +5V.

On the J1 Option Connector, connect the cathode side of the remote Fault LED to 
pin 2, Fault LED. Connect the anode side of the LED to pin 11, +5V.

3.4.2.5

No Wide (Enable Narrow Mode) 

Wide Data Transfer (WDTR) negations can be limited to 8-bit transfers by installing 
a jumper across pin pairs 23/24 (No Wide) of the J3 Option Header. 

3.4.2.6

On-board Busy and Fault Indicators

The drive has an on-board green ‘Busy’ LED and a yellow ‘Fault’ LED.

Summary of Contents for Atlas SCSI Drive 15K II





































































































































































































































































Reviews:

No comments