manualshive.com logo in svg

Maxtor Atlas SCSI Drive 15K II, Product Manual

The Maxtor Atlas SCSI Drive 15K II is a high-performance storage solution for demanding applications. To get the most out of this powerful device, make sure to download the free Product Manual from our website. Gain comprehensive knowledge and optimize your experience with this cutting-edge storage solution.

Share
Download
background image

 SCSI Description

5-106

Maxtor Atlas 15K

5.28.1

Supported Diagnostics Pages Page (00h)

Table 5-153 shows the format of the Supported Diagnostics Pages page. 

Table 5-153   

Supported Diagnostics Pages Page-Data Format

To obtain the Supported Diagnostics Pages list, the initiator must:

1. Send a Supported Diagnostics Page to the drive with a SEND DIAGNOSTICS 
command (the Page Length in the Supported Diagnostics page must be 0).

2. Send a RECEIVE DIAGNOSTIC RESULTS command to the drive. The listing of 
Supported Diagnostic Pages is returned by the drive.

5.28.2

Translate Address Page (40h)

The Translate Address Page allows the initiator to translate a logical sector address, 
physical address, or physical bytes for an index address into any one of the other 
formats. The address to be translated is passed to the drive with the SEND 
DIAGNOSTIC command, and the results are returned to the initiator by the 
RECEIVE DIAGNOSTIC RESULTS command. 

Bit

Byte

7

6

5

4

3

2

1

0

0

Page Code (00h)

1

Reserved

2 - 3

Page Length (0002h)

4

Supported Diagnostics Pages Page (00h)

5

Translate Address Page (40h)

Summary of Contents for Atlas SCSI Drive 15K II





































































































































































































































































Reviews:

No comments

Related manuals for Atlas SCSI Drive 15K II

LaCie Mobile Drive Manual preview
Mobile Drive
Brand: LaCie Pages: 25
OEM Tools 24739 Operating Instructions And Parts Manual preview
24739
Brand: OEM Tools Pages: 4
Backyard Products GABLE Assembly Manual preview
GABLE
Brand: Backyard Products Pages: 72
Seagate Hawk 1 ST11200N Product Manual preview
Hawk 1 ST11200N
Brand: Seagate Pages: 84
Supero 6027R-E1R12N User Manual preview
6027R-E1R12N
Brand: Supero Pages: 112
Sans Digital AccuRAID AR316X12 Quick Installation Manual preview
AccuRAID AR316X12
Brand: Sans Digital Pages: 8
garofalo HIMALAYA 100.S/2/CC User Manual preview
HIMALAYA 100.S/2/CC
Brand: garofalo Pages: 12
LaCie 301273 User Manual preview
301273
Brand: LaCie Pages: 27
Maxtor DiamondMax Plus9 120GB AT Product Manual preview
DiamondMax Plus9 120GB AT
Brand: Maxtor Pages: 79
7-BIT Wicher CD32 User Manual preview
Wicher CD32
Brand: 7-BIT Pages: 4
Quantum DLT 1 Install Manual preview
DLT 1
Brand: Quantum Pages: 3
Tandberg Data SDLT220 Product Manual preview
SDLT220
Brand: Tandberg Data Pages: 142
Conrad 417620 Operating Instructions preview
417620
Brand: Conrad Pages: 4
Netstor NA380A-G3 User Manual preview
NA380A-G3
Brand: Netstor Pages: 11
LOOQS MB202 User Manual preview
MB202
Brand: LOOQS Pages: 69
HermanMiller Meridian Disassembly For Recycling preview
Meridian
Brand: HermanMiller Pages: 5
Würth ORSY Flex 350 Operating Instructions Manual preview
ORSY Flex 350
Brand: Würth Pages: 196
Seagate U Series 9 CE Installation Manual preview
U Series 9 CE
Brand: Seagate Pages: 2

Brands by name

Popular brands

Load more brands