manualshive.com logo in svg

Maxtor Atlas SCSI Drive 15K II, Product Manual

The Maxtor Atlas SCSI Drive 15K II is a high-performance storage solution for demanding applications. To get the most out of this powerful device, make sure to download the free Product Manual from our website. Gain comprehensive knowledge and optimize your experience with this cutting-edge storage solution.

Share
Download
background image

 SCSI Description

5-72

Maxtor Atlas 15K

RPL 

Rotational Position Locking is used for spindle synchronization in storage 
arrays. The modes are:
00b – Disabled
10b – Master
01b – Slave
11b – Not supported
RPL can be overridden if the Maxtor (Vendor) Special Function Control 
page Auto field value = 1. This drive does not support spindle synchroniza-
tion.

Rotational Offset

Rotational Offset indicates the amount of rotational offset that the drive 
uses when synchronized. The rotational offset is applied in the retarded di-
rection (lagging the synchronized spindle master). The value in the field is 
determined by the following formula:
Offset

 

= 0 … 255

256

For example, a numerator of 128 indicates an offset of 1/2 revolution 
(180°).

The valid parameter values are 0 to 255.

The specified value may be rounded. Rotational offset is not used when the 
drive is configured as the synchronized-spindle master.

Medium Rotation Rate

The disk rotation speed in RPM.

Field

Description

Summary of Contents for Atlas SCSI Drive 15K II





































































































































































































































































Reviews:

No comments

Related manuals for Atlas SCSI Drive 15K II

G-Technology G-SPEED FC Product Manual preview
G-SPEED FC
Brand: G-Technology Pages: 17
V-TAC VT-5139 Instruction Manual preview
VT-5139
Brand: V-TAC Pages: 28
Seagate ST94015A Product Manual preview
ST94015A
Brand: Seagate Pages: 46
IBM DDS Generation 6 USB User Manual preview
DDS Generation 6 USB
Brand: IBM Pages: 11
Palram Skylight Instructions Manual preview
Skylight
Brand: Palram Pages: 81
Sony MSH-128 Operating Instructions preview
MSH-128
Brand: Sony Pages: 2
Sony MSG-128A Specifications preview
MSG-128A
Brand: Sony Pages: 2
Sony MSA1GU2 - 1GB Memory Stick Micro M2 Instruction Manual preview
MSA1GU2 - 1GB Memory Stick Micro M2
Brand: Sony Pages: 2
Sony MSA-16A Operating Instructions preview
MSA-16A
Brand: Sony Pages: 2
Sony MS-MT16G Operating Instructions preview
MS-MT16G
Brand: Sony Pages: 1
Sony MS-JX8G Operating Instructions preview
MS-JX8G
Brand: Sony Pages: 1
Sony MSA-8A Operating Instructions preview
MSA-8A
Brand: Sony Pages: 2
Sony MS-MT1G Operating Instructions preview
MS-MT1G
Brand: Sony Pages: 2
Sony MS-HX16G Operating Instructions preview
MS-HX16G
Brand: Sony Pages: 2
Sony MS-A512N Quick Start Manual preview
MS-A512N
Brand: Sony Pages: 2
Okofen S158 EN 2.1 Installation Manual preview
S158 EN 2.1
Brand: Okofen Pages: 16
Spectra Logic Spectra 10000 Replacement Manual preview
Spectra 10000
Brand: Spectra Logic Pages: 21
Spectra Logic T-Series Spectra T200 User Manual preview
T-Series Spectra T200
Brand: Spectra Logic Pages: 110

Brands by name

Popular brands

Load more brands