manualshive.com logo in svg

Maxtor Atlas SCSI Drive 15K II, Product Manual

The Maxtor Atlas SCSI Drive 15K II is a high-performance storage solution for demanding applications. To get the most out of this powerful device, make sure to download the free Product Manual from our website. Gain comprehensive knowledge and optimize your experience with this cutting-edge storage solution.

Share
Download
background image

SCSI Description

Maxtor Atlas 15K

5-71

5.16.3

Rigid Disk Geometry Page (04h)

The Rigid Disk Geometry Page describes the drive geometry. The data format and 
field descriptions are described in Table 5-99 and Table 5-100 respectively.

Table 5-99   

Rigid Disk Geometry Page-(Page 4)

Table 5-100   

Rigid Disk Geometry Page-Field Descriptions (Page 4)

Bit

Byte

7

6

5

4

3

2

1

0

0

PS

Rsvd

Page Code (04h)

1

Page Length (16h)

2 - 4

Number of Cylinders

5

Number of Heads

6 - 8

Starting Cylinder - Write Precompensation

9 - 11

Starting Cylinder - Reduced Write Current

12 - 13

Drive Step Rate (0)

14 - 16

Landing Zone Cylinder

17

Reserved

RPL

18

Rotational Offset

19

Reserved

20 - 21

Medium Rotation Rate

22 - 23

Reserved

Field

Description

PS

Parameters Savable. This bit is only used with the MODE SENSE com-
mand. A returned value of 1 indicates that the target is capable of saving the 
page in a non-volatile, vendor-specific location. The bit is reserved with the 
MODE SELECT command.

Number of Cylinders

The number of physical cylinders that hold host data.

Number of Heads

The number of heads that can access host data.

Starting Cylinder 

The value in this field is the physical cylinder at

Write 

Precompensation

which write precompensation is to begin. The first cylinder number is 0. If 
the starting cylinder is equal to the value in the Number of Cylinders field, 
write precompensation is disabled.

Starting Cylinder 

Reduced Write 

Current

The value in this field is the physical cylinder at which write current is re-
duced. The first cylinder number is 0. If the starting cylinder for reduced 
write current is equal to the value in the Number of Cylinders field, reduced 
write current is disabled.

Drive Step Rate

Applies to stepper-motor actuators. Not applicable.

Landing Zone 

Cylinder

This field indicates a two’s complement location where the drive positions 
the disk heads. A negative value indicates that the heads are positioned be-
low cylinder 0 by that number of cylinders. A positive value greater than the 
number of cylinders indicates that the heads are positioned beyond the cyl-
inders used for data storage at the location specified.

Summary of Contents for Atlas SCSI Drive 15K II





































































































































































































































































Reviews:

No comments

Related manuals for Atlas SCSI Drive 15K II

Omlet Eglu Go Up Instruction Manual preview
Eglu Go Up
Brand: Omlet Pages: 4
Euromate 126060 Instruction Manual preview
126060
Brand: Euromate Pages: 23
V-TAC VT-5139 Instruction Manual preview
VT-5139
Brand: V-TAC Pages: 28
Apricorn Aegis Bio 3.0 Quick Start Manual preview
Aegis Bio 3.0
Brand: Apricorn Pages: 4
Holzmann WB210 Assembly Instruction Manual preview
WB210
Brand: Holzmann Pages: 20
Magnusson MDWT301 Manual preview
MDWT301
Brand: Magnusson Pages: 18
IBM DCS3700 Quick Start Manual preview
DCS3700
Brand: IBM Pages: 21
Vivo DESK-E144WC Instruction Manual preview
DESK-E144WC
Brand: Vivo Pages: 8
Acer USB2.0 Flash Stick User Manual preview
USB2.0 Flash Stick
Brand: Acer Pages: 11
Acer CFE100 Quick Start Manual preview
CFE100
Brand: Acer Pages: 24
Acer USB 2.0 Flash Stick User Manual preview
USB 2.0 Flash Stick
Brand: Acer Pages: 12
Acer RAID Ready Systems User Manual preview
RAID Ready Systems
Brand: Acer Pages: 21
Acer External Hard Disk Drive 500Gb Quick Installation Manual preview
External Hard Disk Drive 500Gb
Brand: Acer Pages: 2
Lenovo Storage N4610 User Manual And Hardware Maintenance Manual preview
Storage N4610
Brand: Lenovo Pages: 176
Seagate ST750UM000 Product Manual preview
ST750UM000
Brand: Seagate Pages: 27
Gateway Computer Drive User Manual preview
Computer Drive
Brand: Gateway Pages: 58
Salsbury Industries S-54000 Series Installation Instructions preview
S-54000 Series
Brand: Salsbury Industries Pages: 5
Transcend StoreJet 18 mobile User Manual preview
StoreJet 18 mobile
Brand: Transcend Pages: 21

Brands by name

Popular brands

Load more brands