manualshive.com logo in svg

Maxtor Atlas SCSI Drive 15K II, Product Manual

Share
Download
Maxtor Atlas SCSI Drive 15K II Product Manual Download Page 116

 SCSI Description

5-50

Maxtor Atlas 15K

RCD

0 

Read Cache Disable. The default value of 0 enables the read cache capability 
and allows the drive to use cache-resident data or medium data to satisfy a 
READ command.

When the value is 1, read caching is disabled and the data returned in response 
to a READ command is fetched from the medium and not from the drive’s cache 
memory.

Demand Read Re-

tention 

Priority

0

This field advises the drive on the retention priority to assign data read into the 
cache that has also been transferred from the drive to the initiator. Not supported 
by the drive.

Demand Write Re-

tention 

Priority 

0

This field advises the drive on the retention priority to assign data written into 
the cache that has also been transferred from the cache memory to the medium. 
Not supported by the drive.

 Disable 

Pre-Fetch Transfer 

Length

 FFFFh

This field specifies the selective disabling of anticipatory pre-fetch
on long transfer lengths. The value in this field is compared to the number of 
sectors requested by the current READ command. If the number of sectors is 
greater the than the value specified, anticipatory pre-fetch is not performed for 
the command. When 0, anticipatory pre-fetch is disabled. Ignored by the drive.

Minimum 

Pre-fetch

0

This field indicates the number of sectors that are to be pre-fetched. See also 
MF.

Maximum 

Pre-fetch 

0x7F5

This field indicates the maximum amount of data to pre-fetch into the cache as 
a result of one READ command. Not supported by the drive. 

Maximum 

Pre-fetch 

Ceiling

0x7F5

Specifies an upper limit on the number of logical blocks computed as the max-
imum pre-fetch. If this number of sectors is greater than the maximum pre-
fetch, then the number of logical blocks to pre-fetch is reduced to the value 
stored in the maximum pre-fetch ceiling field. Not supported by the drive.

FSW

0

The Force Sequential Write bit. Not supported by the drive.

LBCSS

0

The Logical Block Cache Segment Size bit. Not supported by the drive.

DRA

0

The Disable Read-Ahead bit. Not supported by the drive.

VS

The Vendor-Specific bits. Not supported by the drive.

Number of Cache 

Segments

0x15

Ignored by the drive.

Cache Segment Size

0 

Not supported by the drive. 

Non-Cache Segment 

Size

0 

Not supported by the drive. 

Field

 Default 

Value

Description

Summary of Contents for Atlas SCSI Drive 15K II





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands