English
- 24 -
service provider. A firewall might be the reason of a
connectivity problem.
DisplayPort
DisplayPort version 1.2 is supported via the Display-
Port input and output connectors on your Display.
DP Stream Setting
option in the
Settings>Sys-
tem>More
menu is set as
MST
(Multi-Stream Trans-
port) by default. If a MST compliant source device is
connected to the Display, the streaming data should
be configured on the source device (Daisy-chaining).
If DisplayPort version 1.1 compliant or SST (Single-
Stream Transport) compliant source device with
DisplayPort version 1.2 support is connected to the
Display, DisplayPort output on the Display will work as
a splitter. In this case, same image will be displayed
in all connected Displays.
To be able to stream the same image to all connected
Displays using a MST compliant device,
DP Stream
Setting
option in the
Settings>System>More
menu
should be set as
SST
.
The maximum amount of the Displays that can be
connected by using daisy-chaining function may differ
depending on the source device’s capacity. The image
that will be displayed in all Displays will be defined by
the source device. For example, to be able to stream
4 different FHD images, the source device should be
capable of supporting this operation.
Note:
It is recommended to use a DisplayPort certified cable
for connection.
In
SST
operation mode the total amount of the Displays is
limited (a maximum of 7 units) due to HDCP encryption. If
the signal is stable and there is no cable loss, there will be no
limitation in case the source content is not HDCP-encrypted.
When using cascade-connected Displays, it is recommended
to set the
DP Stream Setting
as
SST
on all Displays in SST
operation mode.
For proper operation in
MST
operation mode make sure your
source device is MST compliant. If your source device is a
computer check the specifications of its graphic card to ensure
MST
compatibility. When using daisy-chained Displays, it is
recommended to set the
DP Stream Setting
as
MST
on all
Displays in MST operation mode.
HDMI Out
The HDMI port located on the rear left side of the
Display functions as an output port (upper HDMI port,
HDMI Out). This port will not function as an input,
thus no source devices should be connected to this
port. Only the content received from the HDMI input
port located also on the rear left side of the Display
(lower HDMI port, HDMI1 In) can be outputted from
this port. The contents received from other inputs,
such as VGA or Display Port, can not be outputted.
This is a default function and you can not disable/
enable through any menu option. HDMI output port
will always function if a source device is connected
to the specified HDMI input.
Real Time Clock (RTC)
Your Display has an RTC. It is used to maintain the
real date and time information for a period of time if
the energy supply is interrupted by separating the
Display from the mains or by a power blackout. In this
case the Display will use the date and time information
stored in RTC.
•
All time sources are able to override RTC date/time.
•
Display tries to connect to the
NTP server
period-
ically (6 hours after last update) to get the current
date and time information. If the Display successfully
gets these informations from the NTP server, it
updates itself and RTC with the received date and
time information. If the NTP server update fails, the
Display uses RTC time and date to update itself.
•
The RTC battery provides power to the integrated
real-time clock and the calendar. Without any
external power source, RTC is able to function for
a minimum of 14 days.
• If RTC is used as time source, manual date-time set
is enabled from
Date/Time
option in the
Settings>
System
menu.
Crestron Connected
- In order to work with Crestron Connected protocol,
“CrestronConnected” profile option should be enabled.
- Flash UI which is served by the display device is not
supported. Flash UI which is served by the control
system can be used. Flash UI will not be directly
connected to display device but will be connected
indirectly over control system in this case.
- Configuration page to set control system ip address/
hostname, ip id, and port can be reached by writing
the ip address of display to the browser address bar
on your computer.
- If SecureCommand profile option is enabled,
configuration page is opened with a password dial
og.
After entering the correct password configuration
dialog appears. Password is the same with the one
used in SETUSERSECLEVEL command.
