background image

4

A

  Install the gate operator only when:

   

1

  The operator is appropriate for the construction of the gate and the usage Class of the gate,

   

2

  All exposed pinch points are eliminated or guarded.

B

  The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a separate access  

  opening. The pedestrian access opening shall be designed to promote pedestrian usage. Locate the gate such that persons 
  will not come in contact with the vehicular gate during the entire path of travel of the vehicular gate.

C

  The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent structures when 

  opening and closing to reduce the risk of entrapment. Swinging gates shall not open into public access areas.

D

  The gate must be properly installed and work freely in both directions prior to the installation of the gate operator.

  Do not over-tighten the operator clutch or pressure relief valve to compensate for a damaged gate.

E

  For gate operators utilizing Type D protection:

   

1

  The gate operator controls must be placed so that the user has full view of the gate area when the gate is moving,

   

A gate operator shall additionally be provided with a placard that is marked in letters at least 1/4-in (6.4-mm) high with 

   the 

word 

WARNING

” and the following statement or the equivalent: 

“Moving Gate Has Potential of Inflicting Injury or 

      Death - Do Not Start Gate Unless Path is Clear”

.

   

3

  An automatic closing device (such as a timer, loop sensor, or similar device) shall not be employed, and

   

4

  No other activation device shall be connected.

F

  Controls intended for user activation must be located at least ten feet (10’) away from any moving part of the gate and where 

  the user is prevented from reaching over, under, around or through the gate to operate the controls. Outdoor or easily 
  accessible controls shall have a security feature to prevent unauthorized use.

G

  The Stop and/or Reset button must be located in the line-of-sight of the gate. Activation of the reset control shall not cause 

  the operator to start.

H

  A minimum of two (2) WARNING SIGNS shall be installed, one on each side of the gate where easily visible.

I

  For gate operators utilizing a non-contact sensor:

   

1

  See instructions on the placement of non-contact sensors for each Type of application,

   

2

  Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle, trips the sensor while the gate is 

      still moving, and

   

3

  One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, such as the 

      perimeter reachable by a moving gate or barrier.

J

  For a gate operator utilizing a contact sensor:

   

1

  One or more contact sensors shall be located where the risk of entrapment or obstruction exists, such as at the leading 

      edge, trailing edge, and post mounted both inside and outside of a vehicular horizontal slide gate.

   

2

  One or more contact sensors shall be located at the bottom edge of a vehicular vertical lift gate.

   

3

  One or more contact sensors shall be located at the pinch point of a vehicular vertical pivot gate.

   

4

  A hardwired contact sensor shall be located and its wiring arranged so that the communication between the sensor and 

      the gate operator is not subjected to mechanical damage.

   

5

  A wireless device such as one that transmits radio frequency (RF) signals to the gate operator for entrapment protection 

      functions shall be located where the transmission of the signals are not obstructed or impeded by building structures  
      natural landscaping or similar obstruction. A wireless device shall function under the intended end-use conditions.

   

6

  One or more contact sensors shall be located on the inside and outside leading edge of a swing gate. Additionally, if the 

      bottom edge of a swing gate is greater than 6 inches (152 mm) above the ground at any point in its arc of travel, one or 
      more contact sensors shall be located on the bottom edge.

   

7

  One or more contact sensors shall be located at the bottom edge of a vertical barrier (arm).

ul 325 compliant

installation requirements

Summary of Contents for Phantom 2000















































Reviews: