Max Phantom 2000, Installation And Owner'S Manual

Page: 36 / 46

34
Open RIGHT
Power
INPUTS
MC-100
JOG
RIGHT
JOG
LEFT
UL
Entrap
Matrix
On Line
ERD
Sensitivity
Photo
Cell
Limit SW
On Line
Edge 2
Edge 1
Edge 1 Edge 2
Photo Cell
GND
Jog R
T
Jog L
T
MOTOR OVERLOAD
Motor Controller
ERD
Min
Max
Sensitivity
1 1
5
V
AC
ON
POW
ER
OF F
MA
X P
S-24
PO
WE
R SUPPL
Y
FUSE
7 AM
P
IN
Ma
de
in
USA
POWE
R IN
PO
WER
/SO
LAR
IN
BA
TTER
Y
IN
www
.m ax.u
s.co
m
Ma
de in
US
A
BA TTE
RY
PAC
K
TO MOT
OR
CON
TRO
LLE
R
E
1/2
Ba
tter
y Voltage
Repl
ace
Batter
y TEST
Batt
ery
ON/OF
F Batt
ery
PWR
IN
Error
F
MAX BC-7
Batt
ery Mo
dul
e
Po
wer
INP
UT
S
MC
-10
0
JOG
RIGH
T
JOG LE FT
UL
En tra
p
Ma trix
On
Lin e
ER D
Se
ns
itiv ity
Ph oto
Ce
ll
Limi
t S W
On
Li ne
Ed
ge 2
Ed
ge
1
Edg
e 1 Ed
ge 2 Ph
oto Ce
ll
GN
D
Jo
g R
T
Jo
g LT
M OT
OR
OVE
RLOAD
M oto
r C
on
tro
lle r
ERD
Mi n
Ma
x
The limit tabs need to be set BEFORE the gate can be cycled or DAMAGE could occur.
Approximate OPEN and CLOSED
limit tab positions.
OPEN LED
OPEN LED
CLOSED Tab
Activated
Position
CLOSED Tab
Activated
Position
OPEN Tab
Activated
Position
OPEN Tab
Activated
Position
Push and HOLD the JOG LEFT or JOG RIGHT
buttons accordingly on the MAX MC-100 motor
controller to move the gate (release the button to
stop gate). This allows gate to be moved back and
fourth without leaving the operator to “fine tune”
the open and close gate positions if desired.
Adjustments
open and close limits
CLO
SED
LIM
IT
OPEN
LIMIT
Limit
Switch Box
OPEN Limit
switch contact
point.
CLOSED Limit
switch contact
point.
IMPORTANT: Manually Release arm and move the
gate to the desired OPEN and CLOSED positions to
adjust the limit tabs. Make sure power is ON .
Arm
Opening Direc
tio
n
Arm
Opening Direc
tio
n
Arm Closed Position
Arm Closed Position
Arm Open Position
Arm Open Position
Open
Limit Switch
Closed
Limit Switch
CLOSED LED
CLOSED LED
Open LEFT
R
ot
at
e
L
im
it
T
a
b
u
nt
il
LE
D
li
gh
ts
CLOSED
LIMIT
OPEN
LIMIT
Arm in CLOSED
position
Operator
Opens RIGHT
ADJUST LIMITS:
CLOSED LOSE LOSE
LIMIT LIMIT LIMIT LIMIT LIMIT LIMIT LIMIT
LED
lights
Limit
Tab Screw
1. Move gate to OPEN position.
2. Loosen open limit tab screw.
3. Rotate open limit tab until open
LED lights.
4. Tighten open limit tab screw.
5. Move gate to CLOSED position.
6. Loosen closed limit tab screw.
7. Rotate closed limit tab until closed
LED lights.
8. Tighten closed limit tab screw.
Cycle the gate OPEN and CLOSED after the limit
tabs have been set AND the arm is SECURE .
Operator will cycle slowly to LEARN the open and
closed gate positions. After the operator learns
the gate positions, it will cycle at the GATE SPEED
selected for normal operation.
Manually Release Arm
“Fine Tune” Limits Adjustment
IMPORTANT: Manually Secure Arm (see page 35)
IMPORTANT: LEDs MUST light up when gate
reaches OPEN and CLOSE positions or operator
WILL NOT learn gate positions. If gate positions
are not learned, gate cycling speed will remain
slow during normal operation.
EXAMPLE:
LED Indicators
IMPORTANT:
Remove breather
pin from gear
reducer
BEFORE
cycling operator.
WARNING: Avoid moving arm while “Fine Tune” adjusting.
Breather Pin
CAUTI
ON
REMOVE
BEFORE
OPERA
TIO
N