background image

42

Maximum Controls LLC (“Manufacture”) warrants the original purchaser of this 
product, for the purpose to which this product is originally installed, that the product is 
free from defect in materials and/or workmanship for a period of 8 years for the 
Brushless DC Motor and cover, 5 years for everything else with the exception of the 
batteries which are limited to a 1 year warranty. The performance of this product is 
dependent on compliance to the instructions, maintenance, operation, and testing 
clearly outlined in the user manual. Failure to comply completely with those instructions 
will void this warranty in its entirety. This warranty does not cover damage to the 
product caused by vandalism, water damage, direct hit lightning strike, or installation 
errors.  This warranty does not include any labor charges that might be needed to 
troubleshoot, replace, or repair a problem.

If, during the limited warranty period, one of the components exhibits a defect in 
material and/or workmanship, please call 949-699-0220 before dismantling the product. 
Shipping instructions and an RMA (Return Material Authorization) Number will be 
issued by the factory service center when contacted. Do not send any product in for 
service without an RMA number. Shipping charges to and from the factory service 
center for warranty repairs are the responsibility of the customer. Repair or replacement 
of any warranty items is made at the sole discretion of the Manufacturer.

ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO 
ANY WARRANTIES OF MERCHANTABILITY AND SUITABILITY FOR A PARTICULAR 
PURPOSE, ARE LIMITED TO 8 YEARS FOR THE BRUSHLESS MOTOR DC AND COVER, 
5 YEARS FOR EVERYTHING ELSE WITH THE EXCEPTION OF THE BATTERIES WHICH 
ARE 1 YEAR. NO IMPLIED WARRANTIES WILL EXTEND BEYOND THE WARRANTIES 
LISTED ABOVE. Some states do not allow limitations on how long an implied warranty 
last so this limitation might not apply to you.

This Limited warranty does not cover any problems with or relating to, the gate, the gate 
hardware, including but not limited to hinges, rollers, brackets, entry devices etc. Any 
service call that determines the cause of a problem to be external to the product could 
result in a fee. Under no circumstances shall the manufacture be liable for 
consequential, incidental or special damages arising in connection with the use, or 
inability to use, this product. Under no circumstances will the Manufacture’s liability for 
breach of warranty, breach of contract, negligence or strict liability exceed the cost of 
the product covered other liability in connection with the sale of this product.

phantom 2000 warranty

Summary of Contents for Phantom 2000















































Reviews: