manualshive.com logo in svg

Masoneilan SVI II ESD, Installation And Maintenance Manual

Share
Download
Masoneilan SVI II ESD Installation And Maintenance Manual Download Page 95

Masoneilan SVI II ESD Installation and Maintenance Manual 

=

|

 

95

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

Table 10 outlines some effects of parameter changes. 

Step Two

Run autotune again after ensuring the:

Other Issues That Affect Autotune

Valve oscillating fast:

P

 term too high: reduce 

P 

by ½ and try again

Booster too hot (aggressive) open by-pass on booster and try again

Valve oscillation slow - friction:

Increase 

I

 term by 20-25%

Add 

Dead Zone

 – try 0.25%

Valve moves too slowly:

P 

term too low, try increasing by 25%

Stroking time set to non-zero value.

Table 10 Rough Guide to Effect s of Changing PID Values

Parameter

Rise Time

Overshoot

Settling Time

Increase Value

Decrease Value

Increase Value

Decrease Value

Increase Value

Decrease Value

P

Decrease

Increase

Increase

Decrease

Small Effect

Small Effect

I

Small Effect

Small Effect

Decrease

Increase

Decrease

Increase

D

Small Effect

Small Effect

Decrease

Increase

Decrease

Increase

Air supply is sufficient and there are no air 
leaks.

Valve does not have excessive friction.
Add some 

Dead Zone

 (0.25). 

Linkage is not loose or in an improper posi-
tion.

Mounting is installed correctly.

Alarms are cleared.

Magnet is not out of position.

Boosters are not too aggressive.

Solenoid in supply line should have a Cv that 
is .25 or higher.

Summary of Contents for SVI II ESD





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands