manualshive.com logo in svg

Masoneilan SVI II ESD, Installation And Maintenance Manual

Share
Download
Masoneilan SVI II ESD Installation And Maintenance Manual Download Page 94

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

94 

| 

BHGE

Calibration using Auto Tune

WARNING

DO NOT

 

perform STOPS

 

while the valve is controlling the process.

Valve must be isolated from the process before starting 
calibration. Calibration procedure strokes the valve over it’s full 
range.

DO NOT

 

perform AUTO TUNE

 

while the valve is controlling the 

process.

To auto tune the SVI II ESD using the pushbutton display:

1. Press 

*

 to begin Auto TUNE procedure and 

TUNE

 appears. This takes 3 to 10 minutes and 

strokes the valve in large and small steps to set PID parameters for best positioning 
response. 
When auto TUNE proceeds, numerical messages are displayed, indicating the procedure 
is working.

2. When auto TUNE is complete, 

TUNE

 appears.

3. Press 

+

 repeatedly until 

 SETUP

 appears.

4. Press 

*

 to return to 

SETUP

 menu and 

CALIB

 appears. The valve moves to the value set by 

the current calibrator.

5. Stroke the valve through its range to verify that movement is as needed.

6. Press 

+

 to return to 

SETUP

. 

7. Press 

+

 to return to 

NORMAL

 mode.

Troubleshooting Autotune

Autotune, whether using ValVue, pushbuttons, a DD or a handheld, is the best way to tune the 
valve. If it does not work:

Step One

Autotune again using recommended tuning parameters for the valve is use. The SVI ESD 
software help offers you instructions in how to enter these parameters in the Autotune 
procedure. Alternately, Try starting tuning from the 50% position.

Summary of Contents for SVI II ESD





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands