manualshive.com logo in svg

Masoneilan SVI II ESD, Installation And Maintenance Manual

Share
Download
Masoneilan SVI II ESD Installation And Maintenance Manual Download Page 93

Masoneilan SVI II ESD Installation and Maintenance Manual 

=

|

 

93

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

Calibration with Pushbutton Display

CAUTION

Pilot Trim Valve Applications require the use of the Manual Stop 
calibration procedure. Do not run Find Stops or ValVue ESD Setup 
Wizard on valves with Pilot Trim or damage to the valve occurs.

NOTE

Always perform configuration before running calibration 
functions.

In order to calibrate SVI II ESD using the pushbutton display, it must be in SETUP mode. To 
calibrate the SVI II ESD:

1. On power up, if SVI II ESD is not in NORMAL mode, switch to 

NORMAL

 mode.   Display 

alternates between 

POS

 and 

SIGNAL

 indicating 

NORMAL

 mode. 

2. Press 

+

 to access MANUAL mode and 

MANUAL

 appears.

3. Press 

*

 to select the 

MANUAL

 mode and the display alternates between 

POS –M 

and 

SIG

 

indicating 

MANUAL

 mode.

4. Press 

*

 and 

SETUP

 appears.

5. Press 

*

 and 

CONFIG

 appears. 

6. Press 

+

 to display 

CALIB

.

7. Select 

CALIB

 by pressing 

*

. 

STOPS

 appears.

8. Press 

*

 to activate the Find Stops calibration procedure. The valve moves full open and 

back to full closed. Observe all warnings.

9. Press 

*

 to cause the valve to stroke and to automatically calibrate valve travel.

10. Wait until STOPS procedure finishes, press 

+

 twice until 

TUNE

 appears.

Summary of Contents for SVI II ESD





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands