Masoneilan SVI II ESD Installation And Maintenance Manual Download Page 117

Page: 117 / 220

Masoneilan SVI II ESD Installation and Maintenance Manual

117

Figure 69 FAILSAFE Menu

Handheld Communicator

An alternative digital interface to SVI II ESD is the HART

handheld communicator. In order to

communicate with a HART

protocol compliant field device, the Device Description Language

has to be used. A dedicated Device Description, DD, is published by registration with Field
Comm

. When the DD is installed in a host communication device then it can readily access

all the information in the smart field device. The SVI II ESD registered DD is available from Field
Comm

. The SVI II ESD DD can be obtained from the factory or by contacting your local

representative.

WARNING

Do not connect a HART

modem and PC to a control circuit unless

the controller is HART

compatible or has a HART

filter. Loss of

control or a process upset can occur if the controller output circuit
is not compatible with HART

signal.

Do not Connect a PC or HART

modem to an intrinsically safe

circuit except on the safe area side of the barrier. Do not operate a
PC in a hazardous area without compliance to local and plant
regulations.

RESET

FAILSAFE Menu

FAILSAFE

CLR ERR

VIEW ERR

MANUAL MODE

MANUAL

CYCLING MENU

Instant

Action

Pressing *
displays the first
error, pressing again
displays the second error.
Keep pressing to display all errors
until

VIEW ERR

appears.

WAIT

Quickly Flashes

Summary of Contents for SVI II ESD




























































































































































































































Search results

Summary of Contents for SVI II ESD

Reviews:

Brands by name

Popular brands

Masoneilan SVI II ESD, Installation And Maintenance Manual

Search results

Summary of Contents for SVI II ESD

Reviews:

Brands by name

Popular brands