manualshive.com logo in svg

Masoneilan SVI II ESD, Installation And Maintenance Manual

Share
Download
Masoneilan SVI II ESD Installation And Maintenance Manual Download Page 112

© 2017 Baker Hughes, a GE company, LLC. All rights reserved.

112 

| 

BHGE

VIEW DATA Menu

The VIEW DATA menu reads current configuration information, including PST configuration. 
This information cannot be changed from the VIEW DATA menu. Exit from the VIEW DATA 
menu to return to the previous menu.

This menu can be entered either from the MANUAL Mode menu or from NORMAL Mode menu.

When entering VIEW DATA from NORMAL mode the valve shall still respond to changes in set 
point input signal and the displayed values change in accordance with input signal changes. 
When entered from MANUAL mode, the valve is in locked position. The parameters viewable 
by pressing 

+

 and

 -

 are:

SINGLE

ATO or ATC

PSI, BAR, KPA

Viewing Configuration Parameters

To view configuration parameters use the following procedure:

1. If in NORMAL operating mode, press any button.

2. Press 

+

 to move through options until you reach the VIEW DATA menu item.

3. Press

 

*

 to go to VIEW DATA menu (This leaves the valve in NORMAL mode.). If in MANUAL 

mode, press 

+

 repeatedly until the VIEW DATA menu item is reached. Press

 

*

 to select 

VIEW DATA mode.

4. To exit from the VIEW DATA menu, press

 *

 at any menu line. You return to the last 

displayed menu.

Summary of Contents for SVI II ESD





























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands