Masoneilan SVI II ESD Installation And Maintenance Manual Download Page 109

Page: 109 / 220

Masoneilan SVI II ESD Installation and Maintenance Manual

109

ATO / ATC

The positioner must be configured as Air-to-Open, ATO, or as Air-to-Close, ATC. This parameter
is toggled by the

button.

To determine if a direct acting positioner has to be considered ATO or ATC perform the
following test:

WARNING

This procedure can cause the valve to move. Before proceeding be
sure the valve is isolated from the process. Keep hands clear from
moving parts.

1. Apply actuator’s rated pressure to the positioner supply. Do not exceed actuator pressure

rating listed in control valve specification sheet. Damage to the valve stem, shaft, or trim
can occur.

2. Disconnect electrical (4 to 20 mA) input signal from the positioner or set it to less than 3.6

mA.

3. Observe the control valve position. If the valve is closed the actuator is ATO. If the valve is

open it is ATC.

Pressure Units

Select display units for the optional actuator pressure sensor. The available choices are PSI,
BAR or KPA.

The choice applies to local LCD display, ValVue ESD software display, and to HART

Handheld

communicator.

1. Press

to move from PSI to BAR to KPA.

2. Press

to continue to scroll through the config menu.

NOTE

The characteristic configured in the positioner is applied in
addition to the plug characteristic built into the valve trim. Do not
configure a percentage characteristic if the valve has a
percentage plug.

Changing Language

The local display language can be set to English, French, Spanish, Portuguese, Japanese,
Italian or German.

1. Press

to toggle from ENGLISH to other language selections

2. After you have selected the appropriate language, press

to continue to scroll through

Config

menu.

Summary of Contents for SVI II ESD




























































































































































































































Search results

Summary of Contents for SVI II ESD

Reviews:

Brands by name

Popular brands

Masoneilan SVI II ESD, Installation And Maintenance Manual

Search results

Summary of Contents for SVI II ESD

Reviews:

Brands by name

Popular brands