Masoneilan SVI II ESD Installation And Maintenance Manual Download Page 152

Page: 152 / 220

152

BHGE

NVM_WRITE

Yes/No

Yes/Yes

NVM
Write
Fault

1- An error
occurred when
attempting to
write to non-vola-
tile memory.

1- Clear the condi-
tion using ValVue
ESD or HART

Host.
2- If condition per-
sists, replace
device and report
problem at svi-
sup-
[email protected].

IRQ_FAULT

Yes/No

IRQ Fault 1- The circuit

board interrupt
request failed.

1- Clear the condi-
tion using ValVue
ESD or HART

Host.
2- If condition per-
sists, replace
device and report
the problem at
svisup-
[email protected].

TMOUT_-
FLASH_TEST

NA/NA

Yes/Yes

NOT IMPLE-
MENTED

SELF_
CHECK

Yes/No

Self
Check
Error

1-A general self
check failed.

1- Clear the condi-
tion using ValVue
ESD or HART

Host.
2- If condition per-
sists, replace
device and report
problem at svi-
sup-
[email protected].

SOFTWARE

Yes/No

Yes/Yes

Soft-
ware
Error

Operating system
failed in conduct-
ing a task.

1- Clear the condi-
tion using ValVue
ESD or HART

Host.
2- If condition per-
sists, replace
device and report
problem at svi-
sup-
[email protected].

ESD_TRIP
(_ACTIVE)

Yes

No/No

ESD
Valve
Tripped

SVI II ESD suc-
cessfully de-ener-
gized its
pneumatic out-
put.

None. This is a
status to confirm
that SVI II ESD
successfully
de-energized its
output.

Table 13 SVI II ESD Fault Matrix (Continued)

Sequence

Byte

Bit

FAULT Name

Criticality

of Alarm

Auto-

mati-

cally

cleared

Can be

cleared/

Persists

across

resets

Non-
Mas-

kable/

Annunci-

ated

TEXT For

DD &

ValVue

ESD2

English

Probable Cause

English

Recommended

Action

Summary of Contents for SVI II ESD




























































































































































































































Search results

Summary of Contents for SVI II ESD

Reviews:

Brands by name

Popular brands

Masoneilan SVI II ESD, Installation And Maintenance Manual

Search results

Summary of Contents for SVI II ESD

Reviews:

Brands by name

Popular brands