Never feed the shredder with a quantity
of paper exceeding the maximum indi-
cated in the technical details.
Should the machine be overfed, follow the
instructions under „PAPER JAM“.
EMPTYING THE RECEPTACLE:
- Turn the function switch (1) (fig. 1) in position
„
off
“.
- Take the machine and lift it up.
- The receptacle can be emptied easily.
- After the machine has been reset onto the
receptacle, you can continue shredding.
OPERATION
3
TECHNICAL DATA
Cutting width:
7 mm (strips)
Cutting capacity:
5 sheets (70g/m
2
)
Supply voltage:
see name plate
Pre-fusing:
10 amps (slow-blow)
Working width:
220 mm
Noise generation:
70 dBA
Power:
see name plate
Short-time operation:
2 min
Dimensions (WxDxH):
305x175x340 mm
Weight:
Sreceptacle:
approx. 3 kg
GB
MALFUNCTIONS / MAINTENANCE
PAPER JAM:
If too much paper is fed to the cutting system the
cutting system will jam. Proceed as follows:
- Turn the function switch (1) (fig. 1)
briefly
to
position „
rev
“, then in position „
off
“.
- Cutting system runs in reverse, frees excess
paper and stops.
- Tear off the excess paper over the feed slot
and then turn the function switch (1) (fig. 1) to
position „
auto
“.
- The cutting system runs forward and cuts the
remainding paper left in the cutting system.
- Contnue the shredding process with less pa-
per.
MOTOR PROTECTION:
The motor shuts down automatically, should it
become overloaded. Turn the function switch in
position „
off
“.
Allow the motor to cool down for 20 minutes
(depending upon room temperature) and then
continue shredding.
CHECKLIST IN CASE OF MALFUNCTIONS:
If the device does not function, check the follo-
wing:
- Is the
plug connected
to the mains?
- Is the
function switch
(1) on?
- Is there a
paper jam
?
Follow the instructions under „PAPER JAM“.
- has the
motor
been overloaded?
Wait until the motor has cooled, and then re-
start.
If none of the above applies, contact your
dealer.
Note:
For orders of special accessories and spare
parts, please contact your dealer.
IMPORTANT SAFETY NOTES
INITIATION
SCOPE OF APPLICATION:
The document shredder
PAPERMONSTER JU-
NIOR
is a machine for the destruction of common
written material.
The unit should only be fed with
paper!
Shredding other types of materials can
cause injuries (e.g. by splinters of hard
materials) or may damage the shredder
(e.g. destruction of the cutting system).
INSTALLATION:
- Unpack and set machine upright.
- Take the machine and put it onto the receptacle
(trip switch at the back).
- Plug in the machine (for instructions for the
necessary precautions see „TECHNICAL
DATA“.
The socket outlet shall be installed
near the equipment and shall be easily
accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
EXPLANATION OF THE CONTROLS:
1 = Function switch (fig. 1)
(on / off / reverse)
This switch is for the following functions:
- position „auto“
machine is ready for operation
- position „off“
machine is switched off
- position „rev“
cutting blades are reversing
2 = Sensor (forward run) (fig. 2)
The shredding operation is started as soon
as a sheet of paper passes through the feed
slot.
The shredder may not be used as a step
ladder or as a seat. Danger of falling
due to breakage!
FEEDING THE PAPER:
- Turn the function switch (1) (fig. 1) in position
„
auto
“.
- Feed paper through the inlet guide to the cutting
system.
- Machine switches automatically to forward
and draws paper in. The machine switches off
automatically after shredding.
fig. 1
fig. 2
2
1
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by “one person only”.
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.).
<< Keep children away from the machine.
This machine’s design and safety concept
are based on adult dimensions (feeder route,
safety cut-off switches, etc.) to ensure that it
can be operated safely by
adults
only.
<< Repairs may only be performed by trained
personnel.
<< Keep all loose articles of
clothing, ties, jewelery,
long hair or other loose
objects away from ope-
ning, injury may result!
<< Never insert fingers into opening.
Serious injury may result!
<< In case of danger switch the ma-
chine off with the mains switch,
or with the emergency switch, or
unplug the machine.
<< Always unplug the machine from
the mains power supply before
opening the machine.
