Marksman M6A Installation Manual Download

Page: 8 / 28

Harness 3: White 9-Pin Mini Connector

(continued)

Gray Wire: Channel 2 (Trunk

Release) Output

This will become a 1 second pulse

ground by activating Channel 2 on

transmitter for two seconds. The

current capacity of this wire is

200mA. This feature allows you to

remote control trunk release or other

electric device.

Green Wire: (See Alarm Feature

Programming Part 2)

This wire can turn on and off the

remote start system each time it sees a momentary ground signal. This wire is normally used for testing or

activating the remote starter from an after-market alarm system.

White/Black Wire: Negative Safety Shut Down Input

The White/Black wire provides an instant shutdown for the remote start, whenever it is grounded. Connect the

wire to the hood pin switch previously installed. This wire must be routed through a grommet in the firewall and

connected to the hood pin switch. If the pin switch is to be used with an alarm system, connect this wire with

diode. Diodes are required when the hood pin is used as a triggering device. Wire as shown.

White/Violet Wire: Positive Safety Shut Down Input

Important! This connection is a safety wire and must be connected as shown and tested as specified. Failure to

do so may result in personal injury or property damage. See detail or wiring in the following diagram. This wire

may also be used if the vehicle brake light circuit switches ground to the brake lights. An isolation diode must

be used for ground switched brake light circuits and must be connected to the output of the brake switch.
This wire provides an instant shutdown for the remote start, whenever it re12 volts. If the brake lights

switch in the vehicle sw12 volts to the brake light circuit, connect this wire to the output side of the

brake switch. This will allow the remote start to shut down if an attempt is made to operate the vehicle without

the key while running under the control of the remote start. In most vehicles, in order to shift gears, the brake

pedal must be depressed. The brake input will in turn cause the remote start unit to shut off. A relay may be

required if the brake light switch is (-) type.

(Relay Not Supplied)

Output to Power

Trunk Switch

To Co12 Volts

Input to Relay (+ or -)

White 9-Pin

Mini Plug

Gray

Wire

Brake Light

Bulbs

+12 Volts

Switch Closes When

Brake is Depressed

White Violet Wire

Brake

Pedal

To Lights

White 9-Pin

Mini Plug

Wiring

M6A-IM 3/10/05 2:43 PM Page 8

Summary of Contents for M6A




























Search results

Summary of Contents for M6A

Reviews:

Related manuals for M6A

Brands by name

Popular brands

Marksman M6A, Installation Manual

Search results

Summary of Contents for M6A

Reviews:

Related manuals for M6A

Brands by name

Popular brands