Marksman M6A Installation Manual Download

Page: 18 / 28

Before 15 seconds has passed, push and release the valet switch 9

times then push the valet switch a tenth time and hold it down until 5

short chirps/beeps + 1 long chirp beep is heard then release it. You

are now in Stage 2 Remote Start Feature Programming Mode.

9X + 1X (Hold)

One Chirp

Two Chirps

Three Chirps

Four Chirps

Button

LED One Pulse

LED Two Pulse

LED Three Pulse

LED Four Pulse

(Factory Default Setting)

Step 3

Remote Feature Programming

Use the transmitter buttons as illustrated to adjust the features required. Keep re-pressing the transmitter button that

relates to the feature you want to adjust until the correct amount of chirp/beeps is heard. Move on to the next feature.

Exit the programming mode (3 long chirps and 3 parking light flashes to confirm this exit)

Tachometer

Checking Type

RPM Learning Start
Timer:
0.6 second (1 chirp)

0.8 second (2 chirps)
1.0 second (3 chirps)
1.2 second (4 chirps)

1.4 second (5 chirps)
1.6 second (6 chirps)
1.8 second (7 chirps)

2.0 second (8 chirps)
3.0 second (9 chirps)
4.0 second (10 chirps)

Step 2

Voltage Checking

Type

Fixed Crank

Mode

Low Check Level

(Default for

Tach Check Type)

Hi Check Level

(Default for

Voltage Check Type)

Turn the ignition switch from the OFF

position to the ON position 3 times leaving

it in the OFF position the third time.

Step 1

Tachometer Detection Programming

If you have selected tachometer detection, you are required to program 2 additional features as enclosed.
RPM Learning and Crank Detection Level Programming (if needed):

Turn the ignition switch from the

OFF position to the ON position 3

times leaving it in the Off position

the third time.

Step 1

Before 15 seconds has passed, push

and release the valet switch 9 times

then push the valet switch a tenth

time and hold it down until 5 short

chirps/beeps + 1 long chirp beep is

heard then release it.

9X + 1X (Hold)

Step 2

Remote Start Feature Programming Stage 2 (continued)

Press and release the unlock button

one time. 1 chirp to indicate that

you are in RPM learning mode.

Step 3

M6A-IM 3/10/05 2:43 PM Page 18

Summary of Contents for M6A




























Search results

Summary of Contents for M6A

Reviews:

Related manuals for M6A

Brands by name

Popular brands

Marksman M6A, Installation Manual

Search results

Summary of Contents for M6A

Reviews:

Related manuals for M6A

Brands by name

Popular brands