manualshive.com logo in svg

Malibu Boats 2 MXZ, User Manual

The Malibu Boats 2 MXZ offers exceptional performance on the water, and to ensure you make the most of your boating experience, we provide a comprehensive and user-friendly User Manual that you can download for free. Access the manual directly from manualshive.com, empowering you to maximize your time on the water without any hassle.

Share
Download
background image

1-9

Registration

Federal Law requires that all motorboats be registered and that all motorcraft not
documented by the U.S. Coast Guard display registration numbers. In nearly all states,
this means registration with the designated state agency. In a few jurisdictions, the Coast
Guard retains registration authority. Your dealer will either supply registration forms or
tell you where they may be obtained. The agency will supply you with a certificate which
must be carried with you when the boat is in operation. International laws may vary as to
required registration.

Insurance

The boat owner may be legally responsible for damages or injuries caused by both
himself and the operator (if different than the owner). Common sense dictates that you
carry adequate personal liability and property damage insurance on your boat, just as you
would on your automobile. Many states have laws detailing minimum insurance needs.
Your insurance agent or your dealer may be able to supply you with more information.
You should also protect your boat from physical damage or theft.

Boating Safety Education Opportunities

It is recommended that the boat owner/operator obtain boater safety education. If you
have never owned a boat before, you can get an excellent introduction to boat handling
from organizations such as the U.S. Coast Guard, American Red Cross, United States
Coast Guard Auxiliary, or your local boating authority. Even if you are a veteran boater,
these courses will help sharpen your boating skills as well as bring you up to date on
current rules and regulations. See your local boating agency or dealer for information on
classes in your area.

Some states require youths, 16 years of age and younger, to complete a boating safety
course before operating any watercraft. Many others require operators under the age of 18
to be licensed in small boat operation. Boat smart from the start: take a boating safety
course and get a free vessel safety check annually for your boat. For more information,
contact: United States Coast Guard Auxiliary, www.cgaux.org; United States Power
Squadrons, 1-888-FOR-USPS, www.usps.org. 

The following is a list of some other agencies and organizations that offer Water Safety,
First Aid and CPR courses or information. To find boating safety courses in your area,
call your state’s local boating agency or the USCG boating safety course line at 
1-800-336-2628 (1-800-245-2628 in Virginia).

•    USCG Office of Boating (www.uscgboating.org)
•    American Red Cross (www.redcross.org)
•    U.S. Coast Guard Auxiliary (www.cgaux.org)
•    U.S. Power Squadrons (www.usps.org)
•    State Boating Offices
•    Canadian Power and Sail Squadrons (www.cps-ecp.ca)
•    Boat Owners Association of the United States (www.boatus.com)
•    National Safe Boating Council (www.safeboatingcouncil.org) 
•    Water Sports Industry Association (www.wsia.net)
•    European or international organizations

 Chapter 1_15.qxp_ Chapter 1 doc.qxd  6/30/14  3:10 PM  Page 9

Summary of Contents for 2 MXZ















































































































































































































Reviews:

No comments

Related manuals for 2 MXZ

Lagoon 42 User Manual preview
42
Brand: Lagoon Pages: 122
J 110 Reference Manual preview
110
Brand: J Pages: 30
Elan E4 Owner'S Manual preview
E4
Brand: Elan Pages: 69
Scout Boats 245 Dorado Owner'S Manual preview
245 Dorado
Brand: Scout Boats Pages: 116
Grand Banks 36 Operation Manual preview
36
Brand: Grand Banks Pages: 41
Johnson Outdoors Escape Owner'S Manual preview
Escape
Brand: Johnson Outdoors Pages: 28
Grady-White Boats Canyon 271 Owner'S Manual preview
Canyon 271
Brand: Grady-White Boats Pages: 72
Vanguard 15 Rigging Manual preview
15
Brand: Vanguard Pages: 6
Jeanneau Velasco 37 F Owner'S Manual preview
Velasco 37 F
Brand: Jeanneau Pages: 100
grabner HAPPY CAT LIGHT Owner'S Manual preview
HAPPY CAT LIGHT
Brand: grabner Pages: 44
Zodiac PRO 500 Owner'S Manual preview
PRO 500
Brand: Zodiac Pages: 85
Yamaha XLT1200 WaveRunner 2005 Owner'S/Operator'S Manual preview
XLT1200 WaveRunner 2005
Brand: Yamaha Pages: 136
TALAMEX GLA250 User Manual preview
GLA250
Brand: TALAMEX Pages: 51
Paddle King Lo Pro Angler Manual preview
Lo Pro Angler
Brand: Paddle King Pages: 11
Sea Eagle Boats FoldCat 375FC Instruction & Owner'S Manual preview
FoldCat 375FC
Brand: Sea Eagle Boats Pages: 15
Sea Eagle Boats Fishing Explorer 350fx Instruction & Owner'S Manual preview
Fishing Explorer 350fx
Brand: Sea Eagle Boats Pages: 19
Sea Eagle Boats NeedleNose NN126 Instruction & Owner'S Manual preview
NeedleNose NN126
Brand: Sea Eagle Boats Pages: 21
poolstar Coasto RUSSEL 1P User Manual preview
Coasto RUSSEL 1P
Brand: poolstar Pages: 24

Brands by name

Popular brands

Load more brands