background image

215028

40

Revision A

4.1.7

Calibrating Windrower Knife Drive on the Harvest Performance Tracker Display

When the R216 Rotary Disc Header is attached to an M1240 Windrower, the Harvest Performance Tracker (HPT) will
recognize the header ID and configure the windrower accordingly. The rotary disc header must be calibrated to ensure that
the knife drive pump output is accurate.

CAUTION

Before starting the machine, check to be sure all bystanders have cleared the area.

NOTE:

To calibrate the knife drive, the rotary disc header must be attached and engaged. If the rotary disc header is disengaged
when calibration is selected, the message ENGAGE HEADER will appear on the screen.

1016140

A

B

C

Figure 4.51: Opening the Main Menu

1.

Start the engine, and engage the header.

2.

Press soft key 5 (A) to open the HPT main menu.

3.

Use HPT scroll knob (B) or the ground speed lever (GSL)
scroll wheel to scroll to settings icon (C).

4.

Press HPT scroll knob (B) or the GSL SELECT button (not
shown) to activate the settings menu options.

1016143

A

B

Figure 4.52: Windrower Settings Icon and Calibration
Submenu Icon

5.

Scroll to WINDROWER SETTINGS icon (A) and press SELECT.

6.

Scroll to CALIBRATION icon (B), and press SELECT to open
the adjustment page.

NOTE:

The F3 shortcut button on the operator

s console will also

open the WINDROWER SETTINGS menu.

7.

Select KNIFE DRIVE.

ATTACHING ROTARY DISC HEADER TO M1240 WINDROWER

Summary of Contents for R216





































































































Reviews: