M1 Drones M1 STEM Drone Series User Manual Download Page 33 | Manualshive

Page: 33 / 45

background image

8.

Motors are connected to the M1,
M2, M3, M4 plug sockets.

9.

Connect the M1 – M4 motor
plugs to the flight controller.

10. Once all motors are properly

connected, gently push the board
into the airframe mount,
ensuring that the tabs are within
the “c” cutout of the board.

11. The board is fully placed, once it

reaches the stopper tabs.

INSTALLATION (CONT.)

33

«
...
31
32
33
34
35
...
»

Summary of Contents for M1 STEM Drone Series














































Reviews:

No comments

Related manuals for M1 STEM Drone Series

Matrice 200 Series V2

Brand: dji Pages: 87

Brand: dji Pages: 118

Brand: dji Pages: 39

EVO II EnterpriseV3

Brand: Autel Pages: 65

EVO Lite Series

Brand: Autel Pages: 76

Brand: Contixo Pages: 12

Brand: altura Pages: 46

Brand: Sharper Image Pages: 4

Brand: Parrot Pages: 23

Brand: Parrot Pages: 224

Brand: Parrot Pages: 2

Brand: Parrot Pages: 27

Brand: 3DR Pages: 40

Brand: TreasureHunter3D Pages: 30

Brand: Yin Yan Model Tech Pages: 4

Brand: XciteRC Pages: 48

Brand: RadioLink Pages: 15

Brand: RadioLink Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands