M1 Drones M1 STEM Drone Series User Manual Download Page 30 | Manualshive

Page: 30 / 45

background image

1. Press the Main Menu Button
2. Tap on

SYS

3. Under the

SYSTEM

Menu,

tap

Rx Bind

4. The transmitter is now in BIND

mode and ready to bind with the
Flight Controller.

5. NOTE: Radio Transmitter bind

mode will timeout after 30
seconds.

6. Gather Flight Controller Board.
7. Gather supplied 1S LiPo

Battery.

BINDING PROCEDURE (CONT.)

8. Find the

BIND

button.

30

«
...
28
29
30
31
32
...
»

Summary of Contents for M1 STEM Drone Series














































Reviews:

No comments

Related manuals for M1 STEM Drone Series

Brand: GDU Pages: 10

Brand: Beijing TT Aviation Technology Co., Ltd. Pages: 45

Brand: ZERO-X Pages: 24

ROBOMASTER TT Swarm Combo

Brand: dji Pages: 2

Brand: dji Pages: 28

QUADRONE MAX NH90084

Brand: NINCOAIR Pages: 20

Brand: Amcrest Pages: 2

Mantis Q YUNMQA

Brand: YUNEEC Pages: 12

Brand: YUNEEC Pages: 13

Brand: SINOCHIP Pages: 8

SOKAR FPV DRONE

Brand: Skyrc Pages: 2

Brand: Skyrc Pages: 12

Brand: LooLinn Pages: 19

Brand: Brookstone Pages: 11

Flight Force 324185

Brand: Brookstone Pages: 13

Brand: Brookstone Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands