M Solutions MS-TestPro MS103TDs User Manual Download Page 63

Page: 63 / 113

MS-TestPro

User’s Manual

Page 63 of 113

The Basic Analysis page appears as shown in the figure below.

Figure 78: Basic Analysis Page

The basic analysis page displays the following information:

◼

General Link Quality.

Red, yellow, green as defined below.

◼

Transmitter Link Quality.

Red, yellow, green as defined below.

◼

Receiver Link Quality.

Red, yellow, green as defined below.

◼

Green

. The link is functional.

◼

Yellow

. The link is unstable.

◼

Red

. The link is faulty with a

high probability of failure.

◼

Pixel Clock.

The clock frequency of the video transmission. The Pixel Clock values in the

receiver and transmitter screens should be similar.

◼

Chip Type.

The chip model/part number.

◼

Cable Length.

Approximate cable length calculation (accuracy level



10%), in Meters or Feet.

◼

HDMI HPD.

Hot Plug Detection.

Summary of Contents for MS-TestPro MS103TDs


















































































































Search results

Summary of Contents for MS-TestPro MS103TDs

Reviews:

Related manuals for MS-TestPro MS103TDs

Brands by name

Popular brands

M Solutions MS-TestPro MS103TDs, User Manual

Search results

Summary of Contents for MS-TestPro MS103TDs

Reviews:

Related manuals for MS-TestPro MS103TDs

Brands by name

Popular brands