M Solutions MS-TestPro MS103TDs User Manual Download Page 30

Page: 30 / 113

MS-TestPro

User’s Manual

Page 30 of 113

4.2.4.2

EDID Analyzer

You can use EDID to access information on the display capabilities of HDMI sink devices. There are
two test setups that you can use to access the information:

◼

Connecting the MS-TestPro test device to an HDMI sink device via an HDBaseT link.

◼

Connecting the MS-TestPro test device directly to an HDMI cable.

Figure 31: Connecting the MS-TestPro to the HDMI Sink Device

➔

To access display capabilities using EDID:

Connect the MS-TestPro test device to the HDMI sink device using one of the methods
described above.

Tap on the

EDID Analyzer

button to access information on the display capabilities of the

HDMI sink device. The following screen appears, presenting the sink device display
information, and supported display resolutions.

Figure 32: EDID Information Page

Summary of Contents for MS-TestPro MS103TDs


















































































































Search results

Summary of Contents for MS-TestPro MS103TDs

Reviews:

Related manuals for MS-TestPro MS103TDs

Brands by name

Popular brands

M Solutions MS-TestPro MS103TDs, User Manual

Search results

Summary of Contents for MS-TestPro MS103TDs

Reviews:

Related manuals for MS-TestPro MS103TDs

Brands by name

Popular brands