M Solutions MS-TestPro MS103TDs User Manual Download Page 40

Page: 40 / 113

MS-TestPro

User’s Manual

Page 40 of 113

4.2.4.5

HDBaseT Firmware Update

➔

To upgrade 3rd party Tx or Rx remote unit firmware:

Prepare a USB memory stick with the upgrade file

xxx.Hex

in the

root

folder of the stick.

Connect the stick to one of the USB ports in the MS-TestPro device.

Tap on the

HDBaseT FW Update

button on the Tools screen.

Mark

Tx (Rx)

and

Reset

on the next screen.

Select the related file.

Tap on the

Apply

button as shown in the figure below.

Figure 46: HDBaseT Firmware Update

NOTE

Do not switch off the device’s power during the upgrade!

* Firmware updates are available only to 3

party remote Transmitter or Receiver units.

* The HDBaseT firmware of the MS-TestPro Transmitter and Receiver cannot be upgraded.
* An upgrade should only be done by an expert technician and with a file supplied by the manufacturer of the
equipment that will be upgraded.

Summary of Contents for MS-TestPro MS103TDs


















































































































Search results

Summary of Contents for MS-TestPro MS103TDs

Reviews:

Related manuals for MS-TestPro MS103TDs

Brands by name

Popular brands

M Solutions MS-TestPro MS103TDs, User Manual

Search results

Summary of Contents for MS-TestPro MS103TDs

Reviews:

Related manuals for MS-TestPro MS103TDs

Brands by name

Popular brands