background image

end of gang

middle  

of gang

Lutron 

|

 22

Need help? Contact Lutron Technical Support 24/7: 800.523.9466

general information

Dimmers and switches

1. 

 

2. 

  Install in accordance with all national and local 

electrical codes.

3. 

  When there is no ground wire or way to connect 

the wallbox, to ground within the wallbox the NEC

®

 

2005, Article 404-9 allows a dimmer /switch without a 
grounding connection to be installed as a replacement 
(as long as a plastic, noncombustible wallplate is 
used). For this type of installation, cap or remove the 
green ground wire on the dimmer / switch, and use an 
appropriate wallplate (such as Lutron’s Fassada

®

  

series wallplates).

4. 

  Do not paint dimmers / switches or wallplates.

5. 

  Cleaning Instructions: Clean with a soft, damp  

cloth only. Do not use any chemical cleaners.

6.  

Dimmers / switches may not work with dioded light 
bulbs (Sylvania Designer 16

TM

 or Philips PAR-16

TM

).

7.  

Operate system in temperatures between  
0 °C (32 °F) and 40 °C (104 °F).

8.  

Dimmer / switch may feel warm to the touch  
during operation. This is normal.

9.  

Recommended wallbox depth is 2 1/2” minimum.

10. 

When combining dimmers / switches in the same 
wallbox (multi-ganged), the dimmer’s / switch’s load 
capacity must be reduced.

Derating Chart

Model

Not 

Ganged

End  

of Gang

Middle  

of Gang

AR-6D

600 W

500 W

400 W

AR-5ANS

600 W

500 W

400 W

11. Neutral Connections (AuroRa

®

 Switches 

only):

 In most but not all cases, the neutral wire 

in the wallbox will be an insulated white wire. 
The neutral connection is typically a bundle of 
2 or more wires. The neutral wire(s) will 

not

 be 

connected to the original switch. When you have 
identified the neutral connection and the power is 
turned off use the white wire included with your 

AuroRa

 system to connect neutral to the silver 

screw on the 

AuroRa

 switch.

   

NOTE:

 

AuroRa

 dimmers do not require a  

connection to neutral.

See Important Safety Information (p. 2).

To avoid overheating or possible damage to 
dimmer / switch or other equipment follow the 
load capacities in table below for multi-ganged 
dimmers / switches.

CAUTION

CAUTION

Summary of Contents for AuroRa AR-ENT-2S3D Series





























Reviews: