background image

CellPipe

20H User Guide

iii

Safety, Compliance, and Warranty Information

Before handling any Lucent Access Networks hardware product,
read the Edge Access Safety and Compliance Guide, which can be
found at

http://www.lucentdocs.com/ins

. See that guide

also to determine how products comply with the electromagnetic
interference (EMI) and network compatibility requirements of your
country. See the warranty card included in your product package
for the limited warranty that Lucent Technologies provides for its
products.

Security Statement

In rare instances, unauthorized individuals make connections to the
telecommunications network through the use of access features.

Trademarks

Lucent, the Lucent logo, and all Lucent brand and product names
are trademarks or registered trademarks of Lucent Technologies
Inc. Other brand and product names are trademarks of their
respective holders.

Ordering Information

You can order the most up-to-date product information and
computer-based training online at

http://www.lucentdocs.com/ins

.

Feedback

Lucent Technologies appreciates customer comments about this
manual. Please send them to

[email protected]

.

Summary of Contents for 20H









































Reviews: