Appendix G
MTD75 Operation Guide
- 249 -
Appe
ndix G
Current Output Errors
E300 A Current
Output Hardware Fault
E320 B
The current output circuit has detected an error in the current output loop; this is
most commonly due to either a broken loop or too large a load resistor.
E340 C
E360 D
E301
A
Sensor Input < Current Output Zero
E321 B
The sensor input level is below that set for the current output zero.
E341 C
E361 D
E302
A
Sensor Input > Current Output Span
E322 B
The sensor input level is above that set for the current output span.
E342 C
E362 D
E303
A
Sensor Input < Current Output Span
E323 B
The sensor input level is below that set for the current output Span.
E343 C
E363 D
E304
A
Sensor Input > Current Output Zero
E324 B
The sensor input level is above that set for the current output Zero.
E344 C
E364 D
E305
A
Store A Checksum Error
E325 B
The Store A Save for the current output has become corrupted. Check the current
output's settings in the current output menu and then save the settings again in the
Save/Restore menu.
E345 C
E365 D
E306
A
Store B Checksum Error
E326 B
The Store B Save for the current output has become corrupted. Check the current
output's settings in the current output menu and then save the settings again in the
Save/Restore menu.
E346 C
E366 D
E307 A Setup
Checksum
Error
E327 B
The Setup for this current output has become corrupted. Check and correct the
current output’s settings and turn the unit off and on again. If the message persists
please consult with your supplier.
E347 C
E367 D
E308
A
SD Card Checksum Error
E328 B
The SD Card store from which this current output was restored from has become
corrupted. Check the current output's settings and then save the settings again to
the SD card store.
E348 C
E368 D
Digital Input Errors
E380
DIG 1 Store A Checksum Error
E390 DIG
2
The Store A Save for the digital input has become corrupted. Check the digital
input's settings in the digital input menu and then save the settings again in the
Save/Restore menu.
E400 DIG
3
E410 DIG
4
E420 DIG
5
E381
DIG 1 Store B Checksum Error
E391 DIG
2
The Store B Save for the digital input has become corrupted. Check the digital input's
settings in the digital input menu and then save the settings again in the
Save/Restore menu.
E401 DIG
3
E411 DIG
4
E421 DIG
5
Summary of Contents for MTD75
