LS 47200001 User Manual Download Page 134

Page: 134 / 200

Chapter 10 Program Example

10-7

If the above process is completed, all setting is finished.

In order to download the configured information in COM-C module, connection setting is as shown below.

Select [Setting]

– [Device assignment], ‘Device Assignment CIF Serial Driver’ screen is displayed. Select the

COM port connected with Pnet I/F module and Click

‘Connect COM x’ and check the applicable Check box.

Finally, Click the

‘OK’, Communication is available to download connection information.

[Figure 10.1.13] Device Assignment CIF Serial Driver (1)

[Figure 10.1.14] Device Assignment CIF Serial Driver (2)

After connected, select [Online]

– [Download] to download.

[Figure 10.1.15] Download

If setting and download is completed, All setting of SyCon is finished. Before close the SyCon, It is very useful to

save the network file in order to recover the damaged network.

This part explains the automatic setting.

Summary of Contents for 47200001









































































































































































































Search results

Summary of Contents for 47200001

Reviews:

Related manuals for 47200001

Brands by name

Popular brands

LS 47200001, User Manual

Search results

Summary of Contents for 47200001

Reviews:

Related manuals for 47200001

Brands by name

Popular brands