LNC LNC-T800 Operator'S Manual Download Page 62

Page: 62 / 100

LNC-T800

CNC Group Instruction

LNC Technology Co., Ltd.

1.7 Diagnosis Function (DGNOS)

Click

<DGNOS>

to enter the screen containing functions of

【

ALARM

】

【

SYSUPD

【

IOCSA

】

【

MLC2

】

and

【

SYSTEM

】

diagnosis function screen HMI signals and machine status can be obtained, and hence

brings the convenience to maintenance and system test.

1.7.1

ALARM

Click

【

ALARM

】

to enter a minor function display screen which contains

【

ALARM

】

【

WARN

】

【

HISMSG

】

【

LOGHST

】

【

OP LOG

】

functions. When any Alarm or PLC-related operation alarm appears, Alarm or

information is displayed on the monitor. Therefore, operators can use this button to obtain status

explanations.

When problems occur during system operation,alarm information will be generated, and users can depend on

it to find out the problem and resolution. If system gives out an alarm, users operations will immediately be

stopped, and relevant information will be listed on the monitor. When the problem is resolved, click <RESET>

to cancel the status.

When operation caution appears on screen, click

【

HISMSG

】

button for detailed information. The display of a

caution will not interrupt the process of manufacturing, and it just reminds users the solution for certain

condition.

Operation alarm is decided along with the design of PLC LADDER. For example, if the protection door is not

well closed, the mechanism of LADDER will generate an alarm of

【

DOOR NOT CLOSE

】

, and the

malfunction of cooling water circulation for cutting will result in the message of

【

COOLANT LOW

】

, and so on.

Therefore, when an alarm occurs, carefully inspect the condition of the machine and peripheral equipments.

(This section is applicable to tool machine manufacturing personnel.)

The compilation of alarm messages is done by technician of tool machine manufacturing factories in

accordance with the designs of PLC LADDER, and considerations for machine operation. Users should not

change them discretionarily. When machines leave the factory, customers should be immediately informed of

the related instructions. The contents of these alarms should be compact and clear.

Summary of Contents for LNC-T800





































































































Search results

Summary of Contents for LNC-T800

Reviews:

Related manuals for LNC-T800

Brands by name

Popular brands

LNC LNC-T800, Operator'S Manual

Search results

Summary of Contents for LNC-T800

Reviews:

Related manuals for LNC-T800

Brands by name

Popular brands