LNC LNC-T800 Operator'S Manual Download Page 94

Page: 94 / 100

LNC-T800

LNC Controller Operation Instruction

LNC Technology Co., Ltd.

2.2 Program

Edit

This chapter contains instructions on program edit and relevant functions.

2.2.1

Program Edit

1. Switch to Edit mode and make sure machine preparation is done.
2. Open the manufacturing program to be edited.
3. Click

【

FGPROG

】

function button to switch to program edit screen.

4. Input program codes in edit screen.

2.2.2

Line Positioning

To position to certain position of the program, take the following procedures.

1. Switch to Edit mode and make sure machine preparation is done.
2. Click

【

FGPROG

】

function button to switch to program edit screen.

3. Click

【GOTO】

function button, and an input box appears. Input serial number of the line to be positioned

in the input box, and click

【

】

button to position to the appointed line.

2.2.3

Search for Word String

To search for certain word string of the program, take the following procedures.

1. Switch to Edit mode and make sure machine preparation is done.
2. Click

【

FGPROG

】

function button to switch to program edit screen.

3. Click

【

WORDFIND

】

button, and an input box appears. Input word string to be searched in the input box,

and click

【

】

button. Cursor will stayed at the first corresponding word string.

4. If it is not the desired word string. Click

【

WORDFIND

】

again, and the input box appears will contain the

word string input last time. Click

【

】

to keep searching downward. Repeat this procedure until finding

the desired result or reaching the end of program.

2.2.4

Copy Data Segment

To copy certain data segment of the program, take the following procedures.

1. Switch to Edit mode and make sure machine preparation is done.
2. Click

【

FGPROG

】

function button to switch to program edit screen.

3. Move cursor to the first line of the segment to be copied.
4. Click

【

】

to switch function button list and find

【

MARK

】

function button. Click it to highlight the

line.

5. Move cursor to the last line of the segment to be copied.
6. Click

【

MARK

】

again to highlight the whole segment. Click

【

COPY

】

, and move cursor to the position

where to paste the copied program segment.

7. Click

【

BIND

】

to paste the copied segment at where cursor is. The data lines originally at where the

segment is pasted will be moved to behind the segment.

8. Click

【

UNMARK

】

to cancel the highlight, and then data segment copy is done.

Summary of Contents for LNC-T800





































































































Search results

Summary of Contents for LNC-T800

Reviews:

Related manuals for LNC-T800

Brands by name

Popular brands

LNC LNC-T800, Operator'S Manual

Search results

Summary of Contents for LNC-T800

Reviews:

Related manuals for LNC-T800

Brands by name

Popular brands