LG Therma V ZHBW056A0 Service Manual Download Page 44

Page: 44 / 115

- 44 -

Installer setting

• You can set the product user functions.
• Some functions may not be displayed/operated in some product types.

Test

Description

3 Minutes Delay

Factory use only

Select Temperature Sensor

Selection for setting temperature as air temperature or leaving water
temperature or air+leaving water temperature

Dry Contact Mode setting

Dry contact function is the function that can be used only when the dry contact
devices is separately purchased and installed.

Central Control address

When connecting the central control, set the central control address of the unit.

Pump Test run

Water pump test run

Air cooling set temp. setting

Adjusting range of 'Setting Air Temperature' in cooling mode

Water cooling set temp. setting

Adjusting range of 'Setting Leaving Water Temperature' in cooling mode

Air heating set temp. setting

Adjusting range of 'Setting Air Temperature' in heating mode

Water heating set temp. setting

Adjusting range of 'Setting Heating Flow Temperature' in heating mode

DHW Set Temp.setting

Setting DHW set temperature

Screed drying setting

Setting for using Step 1 or 2 capacity of electric

Heater on temperature

Setting outdoor air temperature where half capacity of electric heater starts
operation.

Water supply off temp. during

cooling setting

Determine leaving water temperature when the unit is turned off. This funtion is
used for preventing condensation on the floor in cooling mode

Tank disinfection setting 1

Setting start/maintain time for pasteurisation

Tank disinfection setting 2

Setting pasteurisation temperature

Tank setting 1

Setting start temperature for operation

Tank setting 2

Setting maintain temperature for operation

Heater priority

Determine electric heater and water heater on and off

DHW time setting

Determine follow time duration : operation time of domestic hot water tank
heating, stop time of domestic hot water tank heating, and delay time of DHW
tank heater operating

Use Heating Tank Heater

Change setting value for hot water tank heater operation such as hot water
tank heater use / unused and heater delay time

TH on/off Variable, heating air

setting

Heating air temperature TH On / Off Type setting

TH on/off Variable, heating Water

setting

Heating Water Outlet Temperature TH On / Off Type

Summary of Contents for Therma V ZHBW056A0










































































































Search results

Summary of Contents for Therma V ZHBW056A0

Reviews:

LG Therma V ZHBW056A0, Service Manual, Page: 44 / 115

Search results

Summary of Contents for Therma V ZHBW056A0

Reviews: