LG Therma V ZHBW056A0 Service Manual Download Page 35

Page: 35 / 115

- 35 -

DIP switch information

• If you set Dip switch when power is on, the changed setting will not be applied immediately.

The changed setting will be enabled only when Power is reset or by pressing Reset button.

Option Switch 2

Description

Setting

Default

Role when central
controller is equipped

As Master

As Slave

Accessory installation
information

Unit + Outdoor unit
is installed

Unit + Outdoor unit
+ DHW tank
is installed

Unit + Outdoor unit
+ DHW tank
+ Solar thermal system
is installed

DHW tank is installed

Full capacity is used.

Cycle

Heating Only

Heating & Cooling

Flow switch detection

Always

While water pump is on

Electric heater step

Electric heater is not used

Half capacity is used.

Unused

Thermostat installation
information

Thermostat is NOT installed

Thermostat is installed

Summary of Contents for Therma V ZHBW056A0










































































































Search results

Summary of Contents for Therma V ZHBW056A0

Reviews:

LG Therma V ZHBW056A0, Service Manual, Page: 35 / 115

Search results

Summary of Contents for Therma V ZHBW056A0

Reviews: