LG CodeZero A9 Series Service Manual Download Page 94

Page: 94 / 104

-94-

Only training and service purposes

Failures and measures

Yes

4. Dust bag notification failure

Check Point

Checkpoints

Measures

Dust bag

replacement

notification

failure

Does the Red Led flash when

the operation is carried out

again after the dust bag has

been replaced?

(Red LED Off)

Is the resistance at both ends of

the pressure switch connector

(CN16) 1M Ohm or higher?

Does the red LED still

flash after the pressure

switch connector (CN16)

is removed from the

Main PCBA?

Replace the pressure

switch

(EAD65896502).

Replace the Main

PCBA

(EBR33171201).

Normal operation

The Main PCBA is

normal.

Check the resistance at

both ends of the Main

PCBA CN16 2Pin

Connector.

Measure the resistance at

both ends.

(Normal: 1M Ohm or higher)

Summary of Contents for CodeZero A9 Series



































































Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands

LG CodeZero A9 Series, Service Manual

Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands