LG CodeZero A9 Series Service Manual Download Page 28

Page: 28 / 104

-28-

Only training and service purposes

How to Disassemble, Reassemble and Repair Main Parts

4. How to Replace the Motor Assembly

(1) Disassemble the decor

part using a flat-head

screwdriver. (The part

needs to be replaced if

damaged during

assembly)

(2) Hold the pipe part and

pull.

(3) Loosen the screw at the

bottom of the pipe.

(4) Hold the pipe part and

pull.

(5) Remove the connector

and gasket.

(6) Remove the filter cover

and filter by hand.

(7) Disassemble three

screws from the air

guide.

(8) Remove the product

body, gasket and

harness.

(9) Remove the motor

located in the product

body.

(10) Reassemble following

the reverse order of

disassembly.

※

Note

If the gasket is damaged when replacing

the motor, replace it with insulating tape as

shown in the photograph.

Summary of Contents for CodeZero A9 Series



































































Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands

LG CodeZero A9 Series, Service Manual

Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands