LG CodeZero A9 Series Service Manual Download Page 33

Page: 33 / 104

-33-

Only training and service purposes

How to Disassemble, Reassemble and Repair Main Parts

- How to assemble the Tube

(1) Prepare the tube as

shown in the picture

(2) Pay attention to the

direction of the check

valve arrow and connect

the tube as shown in the

figure.

(3) Assemble the Tube

ⓓ

into the pump`s inlet as

shown in the picture.

Make sure that the

pump`s outlet goes

upward

(4) Assemble the Tube

ⓑ

into the pump`s outlet

as shown in the picture.

(5) Assemble the Tube

ⓒ

(2ea) as shown in the picture.

12. How to Use a Battery Test Jig

1. Prepare a test jig and

battery.

2. Connect the adaptor and

the test jig.

3. Connect the adaptor to

the plug.

4. Turn on the test jig.

5. Press the A9-k button

and check if the light is

on.

6. Fit the battery and press

Start.

7. Check the battery status.

8. Judge whether it is normal or not and determine the

type of defect.

Summary of Contents for CodeZero A9 Series



































































Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands

LG CodeZero A9 Series, Service Manual

Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands