LG CodeZero A9 Series Service Manual Download Page 96

Page: 96 / 104

-96-

Only training and service purposes

Cleaning function operation and error modes

Failure

Cause of failure

How to check

Measures

A9S mount holder

operation failure

The Main PCB is faulty.

Using a tester, check if the Triac (U11) and/or the resistance are

damaged.

Check the output voltage of the PCB terminal (Motor) - Sealing unit

motor: Check if the AC voltage between No. 1 Pin and No. 5 pin of

No. CN21 Connector is 220V.

- Suction opening and closing hole motor: Check if the AC voltage

between No. 3 pin and No. 6 pin of No. CN21 Connector is 110V.

- Dust canister cover hook release unit motor: Check if the DC voltage

Between No. 17 pin(GND) and No. 7 pin(Sig) of CN30 is 5V.

Replace the Main PCB.

Micro Switch failure

An error message displayed (buzzer sounds and 3 Display LEDs

flash at the same time.)

Replace the Micro Switch/

Connector fastened incorrectly

Check the connector fastening and assembly status.

Reassemble or replace the Connector.

Charging station

operation failure

(The product body

cannot be charged

when it is inserted

into the charging

station.)

The Main PCB is faulty.

Check the output voltage of the battery terminal (29.2V)

(Product body battery: When the battery is removed and the output

voltage is measured within 7 seconds of the product body being

installed)

Check the assembly status of the Connector

and then replace the Main PCB.

Connector fastened incorrectly.

Check the connector fastening and assembly status.

Reassemble or replace the Connector.

The battery terminal is faulty.

Using a tester, check if it is disconnected (Main CN28 and the

charging terminal connection harness).

Replace the Harness or the Duct Assembly.

Charging station

operation failure

(The auxiliary

battery cannot be

charged when it is

inserted.)

The Micro Switch on the auxiliary battery is

faulty.

Check if No. 14 pin and No. 16 pin of CN30 are shorted when the

Micro Switch operates.

Replace the Top Cover Assembly.

The Main PCB is faulty.

Check the output voltage of the battery terminal (29.2V) (Auxiliary

battery: If the Micro Switch operates arbitrarily)

Check the assembly status of the Connector

and then replace the Main PCB.

Connector fastened incorrectly.

Check the connector fastening and assembly status.

Reassemble or replace the Connector.

The battery terminal is faulty.

Using a tester, check if it is disconnected (Main CN28 and the

charging terminal connection harness).

Replace the Harness or replace the Top

Cover Assembly.

Summary of Contents for CodeZero A9 Series



































































Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands

LG CodeZero A9 Series, Service Manual

Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands