LG CodeZero A9 Series Service Manual Download Page 13

Page: 13 / 104

-13-

Only training and service purposes

Maintenance

Cleaning

Before Cleaning

•

Never wash the following parts with water:

−

Nozzle

−

Rotating brush

−

Dust bin

•

The power button may be pressed and the product turned on. Always remove the

battery before cleaning the product.

•

Clean the filter periodically to maintain the normal suction power of the product.

•

If the suction power becomes weak or dust is filled to the max. fill line of the dust bin,

empty the dust bin.

Caution

•

Always install the exhaust filter and free filter into the vacuum body after cleaning them.

If you use the product without installing the filters, dust may get into the motor inside the

product and cause failure.

Summary of Contents for CodeZero A9 Series



































































Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands

LG CodeZero A9 Series, Service Manual

Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands