LG CodeZero A9 Series Service Manual Download Page 27

Page: 27 / 104

-27-

Only training and service purposes

How to Disassemble, Reassemble and Repair Main Parts

2. How to Replace the Main PCB

(1) Separate Handy from

the product body.

(2) Remove the button

using a knife or a sharp

object. Insert a label or

something similar to

prevent damage to the

decor.

(The button

needs to be replaced if

damaged)

(3) Loosen the screw at the

button part.

(4) Hold and remove the

bumper by hand.

(5) Remove the harness

attached to the handle.

(6) Remove the power PCB

by hand.

(7) Push the upper hook

part and the main PCB

part.

(8) Pull the main PCB part.

(9) Reassemble following

the reverse order of

disassembly.

3. How to Replace the Wi-Fi PCB

(1) Remove the harness

attached to the handle.

(2) Remove the Wi-Fi

connections.

(3) Reassemble following

the reverse order of

disassembly.

Summary of Contents for CodeZero A9 Series



































































Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands

LG CodeZero A9 Series, Service Manual

Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands