LG CodeZero A9 Series Service Manual Download Page 84

Page: 84 / 104

-84-

Only training and service purposes

Failures and measures

+ -

Yes

2. No dust emptying operation is carried out (1/3)

Check Point

Check if the power

is normal.

(Operating time:

Approximately 10 seconds)

Check if the

product body is

detected

Check settings

and the terminal

power.

Checkpoints

Measures

Does a buzzer sound when

the power cord is connected

initially?

(Display LEDs light in order)

Is the initialization (sealing motor

operation) carried out when the

power cord is connected initially?

Does the cycle begin when

the Start button is pressed?

Is 4~6V measured at

the charging terminal

of the product body?

Measure the terminal

voltage (4~6V).

Does the dust emptying cycle

begin automatically along with

a buzzer sound from the

product body when the

product body is mounted after

the sealing motor is initialized?

Is the automatic mode set?

Move to

“4-1. No power

supply”.

Move to “4-2.

Display

failure”.

Move to “3.

Charging failure”

and check again

Reassemble and

check the Display

PCBA, and then check

again if the product

body is detected.

Reinstall the

product body and

check again to see

if the product body

is detected.

“Move to 4. Dust

emptying

operation (2/3)”

“Move to 4. Dust

emptying

operation (2/3)”

Summary of Contents for CodeZero A9 Series



































































Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands

LG CodeZero A9 Series, Service Manual

Search results

Summary of Contents for CodeZero A9 Series

Reviews:

Related manuals for CodeZero A9 Series

Brands by name

Popular brands